493505
6
Zoom out
Zoom in
Vorherige Seite
1/18
Nächste Seite
IDENTIFICATION OF CONTROLS
FRONT PANEL
1 STANDBY: With the rear panel POWER switch set to ON position,
press this button to switch ON the C 375BEE from standby mode.
The Standby LED indicator will turn from amber to blue. Pressing the
STANDBY button again turns the unit back to standby mode.
The C 375BEE can also be switched ON from standby mode by pressing
any of the front panel buttons.
AUTO STANDBY (FOR 230V VERSION MODEL ONLY)
Auto Standby feature is an integral feature of C 375BEE that conforms
to European ecodesign regulations. The C 375BEE can be setup
to automatically go to standby mode if there is no user interface
interaction and no active source input within 30 minutes. Auto standby
mode can be enabled or disabled by the following steps.
Enable Auto Standby mode
At operating mode, press and hold together STANDBY and MP buttons
until Standby LED ashes once.
Disable Auto Standby mode
At operating mode, press and hold together STANDBY and MP buttons
until Standby LED ashes twice.
2 STANDBY LED: This indicator will light up amber when the C 375BEE
is in standby state. When the C 375BEE is at ON state, this indicator will
illuminate blue. When infrared command from the SR 8 is received, this
indicator will also ash momentarily.
In cases of serious abuse of the C 375BEE, such as excessively low
loudspeaker impedance and short circuit, the C 375BEE will engage its
Protection circuitry, indicated by the Standby LED turning from blue to
red and the sound being muted.
In such a case, turn the C 375BEE OFF by the rear panel POWER switch,
wait for it to cool down and/or check the speaker connections, making
sure the overall loudspeaker impedance doesn’t go below 4 ohms or
8 ohms in Bridge Mode. Once the cause for the protection circuitry to
engage has been removed, switch ON the rear POWER switch and the
STANDBY button to resume normal operation.
3 BRIDGE MODE INDICATOR: This BRIDGE MODE indicator lights up
blue when the C 375BEE is switched to Bridge Mode. Refer also to the
item below about BRIDGE MODE at the IDENTIFICATION OF CONTROLS
– REAR PANEL.
4 SOFT CLIPPING INDICATOR: The blue SOFT CLIPPING LED shows
that the SOFT CLIPPING mode is engaged. Refer also to the item below
about SOFT CLIPPING (item 13) at the IDENTIFICATION OF CONTROLS –
REAR PANEL.
5 MP SOCKET: Using a 3.5mm stereo plug, connect into this socket the
audio output of a Media Player.
NOTES
If an external Media Player is connected to the front MP socket (using a
3.5mm stereo plug) while listening to a MP line-level source, the external
Media Player will be directly selected with the MP line-level source
immediately disconnected.
It is recommended to mute the volume or switch to a dierent input
before plugging/unplugging the external Media Player cable.
6 REMOTE SENSOR: Point the SR 8 remote control at the remote
sensor and press the buttons. Do not expose the remote sensor of the
C 375BEE to a strong light source such as direct sunlight or illumination.
If you do so, you may not be able to operate the C 375BEE with the
remote control.
Distance: About 23ft (7m) from the front of the remote sensor.
Angle: About 30° in each direction of the front of the remote sensor.
7 PHONES: A 1/4” stereo jack socket is supplied for headphone listening
and will work with conventional headphones of any impedance. The
headphone socket will work in parallel to the selected speakers. To
listen to headphones only, de-select Speakers A and/or B. The volume,
tone and balance controls are operative for headphone listening. Use
a suitable adapter to connect headphones with other types of sockets,
such as 3.5mm “personal stereo jack plugs.
NOTE
Make certain that the volume control is turned to minimum (fully
counter-clockwise) before connecting or disconnecting headphones.
Listening at high levels can damage your hearing.
1
12 1311107 8 9
2 3 4 5 6
6
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für NAD C 375 BEE wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von NAD C 375 BEE

NAD C 375 BEE Bedienungsanleitung - Deutsch - 18 seiten

NAD C 375 BEE Bedienungsanleitung - Holländisch - 18 seiten

NAD C 375 BEE Bedienungsanleitung - Französisch - 18 seiten

NAD C 375 BEE Bedienungsanleitung - Italienisch - 18 seiten

NAD C 375 BEE Bedienungsanleitung - Spanisch - 18 seiten

NAD C 375 BEE Bedienungsanleitung - Schwedisch - 18 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info