Bedienungsanleitung NAD C 375 BEE (Seite 7 von 18) (Englisch)

493505

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

8 SPEAKERS A, B: The SPEAKERS A and B buttons engage or disengage

the speakers connected respectively to the SPEAKERS A and SPEAKERS

B terminals on the rear panel. Press “A” to switch ON or OFF the speakers

connected to the SPEAKERS A terminals. Press “B” to switch ON or OFF

the speakers connected to the SPEAKERS B terminals. Press both “A” and

“B” to engage at the same time both SPEAKERS A and SPEAKERS B. The

corresponding blue LED indicator embedded around the SPEAKERS A

and SPEAKERS B buttons will illuminate accordingly when each or both

are engaged.

9 INPUT SELECTORS: These buttons select the active input to the

NAD C 375BEE and the signal sent to the loudspeakers, headphones

and the PRE OUT sockets. The buttons on the remote control handset

duplicate these buttons. When selected, the corresponding input LED

indicator embedded around the bezel of the particular input button will

illuminate blue.

MP (MEDIA PLAYER): Selects a line-level source connected to the MP

sockets as the active input.

If an external Media Player is connected to the front MP socket (using

a 3.5mm stereo plug) while listening to a MP line-level source, the

external Media Player will be directly selected with the MP line-level

source immediately disconnected. It is recommended to mute the

volume or switch to a dierent input before plugging/unplugging the

external Media Player cable.

CD: Selects the CD (or other line-level source) connected to the CD

sockets as the active input.

TUNER: Selects the tuner (or other line-level source) connected to the

tuner sockets as the active input.

DISC/PHONO: Selects a line-level source connected to the DISC

sockets. With the optional PP 375 PHONO MODULE installed, the DISC

input socket is disabled and the PHONO source selected as the active

input.

AUX: Selects a line-level source connected to the AUX sockets as the

active input.

TAPE 2: Selects Tape 2 as the active input.

TAPE MONITOR: Selects the output from a tape recorder when playing

back tapes or monitor recordings that are being made through the Tape

Monitor sockets.

TAPE MONITOR does not override the current input selection. For

example, if CD is the active input when TAPE Monitor is selected, then

the CD signal will continue to be selected and sent to both the TAPE

2 and TAPE Monitor OUTPUT sockets, but it is the sound from recorder

connected to Tape Monitor that will be heard on the loudspeakers.

Apart from the TAPE MONITOR LED illuminated to indicate it is engaged,

the corresponding LED indicator for the active input will also stay

illuminated.

10 TONE DEFEAT: Tone Controls are enabled or disabled by pressing this

button. When enabled (TONE DEFEAT LED indicator is illuminated), the

Tone Control circuits are bypassed. The Tone Control circuits are active

when the TONE DEFEAT LED indicator stays extinguished.

11 TONE CONTROLS: The NAD C 375BEE is tted with BASS and TREBLE

tone controls to adjust the tonal balance of your system. The 12 o’clock

position is “at” with no boost or cut, and an indent indicates this

position. Rotate the control clockwise to increase the amount of Bass or

Treble. Rotate the control counterclockwise to decrease the amount of

Bass or Treble. The Tone controls do not aect recordings made using

the Tape outputs but will aect the signal going to the Pre-amp outputs

(PRE OUT 1 and PRE OUT 2).

12 BALANCE: The BALANCE control adjusts the relative levels of the left

and right speakers. The 12 o’clock position provides equal level to the left

and right channels. A detent indicates this position. Rotating the control

clockwise moves the balance towards the right. Rotating the control

counterclockwise moves the balance to the left. The BALANCE control does

not aect recordings made using the Tape outputs but will aect the signal

going to the Pre-amp output (PRE OUT 1 and PRE OUT 2).

13 VOLUME: The VOLUME control adjusts the overall loudness of the signals

being fed to the loudspeakers or headphones. Turn clockwise to increase

the volume setting; counter clockwise to lower it. The VOLUME control does

not aect recordings made using the Tape outputs but will aect the signal

going to the Pre-amp output (PRE OUT 1 and PRE OUT 2).

IDENTIFICATION OF CONTROLS

FRONT PANEL

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD C 375 BEE Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C 375 BEE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info