Bedienungsanleitung NAD C-427 (Seite 7 von 12) (Englisch)

581050

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

1 FM ANTENNA TERMINAL

• Connect the supplied wire “dipole” FM antenna to the FM antenna

terminal using the supplied “balun” adapter. It will usually work best

when mounted on a vertical surface such as a wall, with arms fully

outstretched forming a horizontal “T” perpendicular to the origin

point of the signal.

AM ANTENNA TERMINAL

• The AM loop antenna supplied with the C 427 (or a suitable

replacement) is required for AM reception. Open the clip terminal

lever; insert the wire making sure to match the color-coded (white

and black) ends of the wire to that of the terminal and close the

lever ensuring that the lever locks the wire in place.

• Testing dierent positions for the antenna may improve reception;

vertical orientation will usually produce the best results. Antenna

proximity to large metal objects (appliances, radiators) may impair

reception, as will attempts to lengthen the wire to the loop.

• If an external AM antenna is used, make connections to the AM

and GND terminals in accordance with the instructions supplied

with the antenna. Refer also to the item about ASSEMBLING THE

LOOP ANTENNA at the LISTENING TO AM/FM RADIO section of the

OPERATION page.

2 AUDIO OUT (L, R)

• Connect to the corresponding analog audio input of an amplier,

receiver or stereo system.

3 RS-232

• Connect this interface using RS-232 serial cable (not supplied) to

any Windows compatible PC to allow remote control of the C427

via compatible external controllers.

• NAD is a certied partner of AMX and Crestron and fully supports

these external devices. Check out the NAD website for information

about AMX and Crestron compatibility with NAD. See your NAD

audio specialist for more information.

• Refer to the NAD website for information about RS232 Protocol

documents and PC interface program.

4 IR IN

• This input is connected to the output of an IR (infrared) repeater

(Xantech or similar) or the IR output of another component to allow

control of the C 427 from a remote location.

• Most NAD products with IR OUT are fully compatible with the C 427.

5 +12V TRIGGER IN

• This input allows the C 427 to be switched remotely to standby

mode and ON by ancillary equipment, such as an amplier, preamp,

AV processor, etc. The controlling device must be equipped with a

12V trigger output to use this feature.

• Connect this +12V trigger input to the remote component’s

corresponding +12V DC output jack using a mono cable with

3.5mm male plug.

6 POWER

• Supply the AC mains power to the C 427.

• When the POWER switch is set to ON position, the C 427 goes to

standby mode as shown by the amber status condition of the

Standby LED. Press the front panel Standby button or remote

control’s [ON] button to switch ON the C 427 from standby mode.

• If you intend not to use the C 427 for long periods of time (such as

when on vacation), switch o the POWER switch.

• With POWER switched o, neither the front panel Standby button

nor remote control’s [ON] button can activate the C 427.

7 AC MAINS INPUT

• The C 427 comes supplied with a separate detachable AC power

cord. Connect corresponding end of the AC power cord to the AC

mains input of the C 427 and the plug connected to a mains power

source.

• Connect only to the prescribed mains power source, i.e., 120V 60

Hz (for 120V version models of C 427 only) or 230V 50 Hz (for 230V

version models of C 427 only).

• Always disconnect the plug from the mains power source rst,

before disconnecting the other end of the AC power cord from the

C 427’s AC Mains input socket.

• If you intend not to use the C 427 for long periods of time,

disconnect the plug from the mains power source.

IDENTIFICATION OF CONTROLS

REAR PANEL

ANTENNA

GND AM

AUDIO OUT

RS232

+12V

TRIGGER

POWER

100~240V – 50/60Hz

IR IN

2 3 54 61

ATTENTION!

Please make sure that the C 427 is powered o or unplugged before making any connections. It is also advisable to power down or unplug all associated

components while making or breaking any signal or AC power connections.

ENGLISHPORTUGUÊS FRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD C-427 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD C-427

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info