Bedienungsanleitung NAD M10 (Seite 7 von 14) (Englisch)

745038

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

ENGLISH

9 LAN/USB

LAN

• LAN connection must be setup for wired connection to be

established. Set up a Wired Ethernet broadband router with

broadband internet connection. Your router or home network

should have a built-in DHCP server to consummate the connection.

• Using a standard straight-through Ethernet cable (not supplied),

connect one end of the Ethernet cable to the LAN port of your wired

Ethernet broadband router and the other end to M10’s LAN port.

NOTES

• NAD is not responsible for any malfunction of the M10 and/or the

internet connection due to communication errors or malfunctions

associated with your broadband internet connection or other

connected equipment. Contact your Internet Service Provider (ISP) for

assistance or the service bureau of your other equipment.

• Contact your ISP for policies, charges, content restrictions, service

limitations, bandwidth, repair and other related issues pertinent to

internet connectivity.

USB

• Connect to this USB port USB mass storage devices formatted as

FAT32, NTFS or Linux ext4. The connected USB device appears as a

Local Source (USB) in the BluOS App.

• Access and playback music stored in the connected USB device by

selecting “USB” from the BluOS App.

10 STANDBY BUTTON

• Press Standby button to switch ON the M10 from standby mode.

The Status indicator will change from amber to solid white.

• Switch back M10 to standby mode by holding down Standby

button until the NAD logo indicator starts ashing red before

turning to solid amber.

11 AC MAINS INPUT

• The M10 comes supplied with two separate mains power cords.

Select the mains power cord appropriate for your region.

• Before connecting the power cord’s plug to the mains power outlet,

ensure that the other end of the power cord is rmly connected to

M10’s AC Mains input socket..

• Always unplug the power cord from the mains power outlet before

disconnecting the other end of the power cord from M10’s AC

Mains input socket.

12 BRIDGE MODE

M10 output power is at least doubled when set to Bridge Mode. This

way, the M10 can be used as part of a high power stereo or home-

theatre system by connecting additional power ampliers.

· In BRIDGE MODE (switch at ON setting), the M10 will produce

approximately 200W into an 8 ohm loudspeaker. In this mode, the

amplier sections will react as though the speaker impedance has

been halved. Low impedance speakers (under 8 ohms) are not

recommended when using Bridge Mode as these may cause the

amplier’s thermal cut-out to operate if played at high levels.

· Set the BRIDGE MODE switch to “ON“ position. Then, connect the

speaker to the rear panel terminals marked “SPEAKER RIGHT +” and

“SPEAKER LEFT +” ensuring that “SPEAKER RIGHT +” is connected to

the “-” terminal of your speaker and “SPEAKER LEFT +” is connected

to the speaker’s “+” terminal.

· Connect the source to the Left input sockets only. Do not connect

anything to the Right Input socket when Bridge Mode is selected.

13 SPEAKERS

• Connect M10’s Right speaker terminals marked “R +” and “R-” to

the corresponding “+” and “-“ terminals of your designated right

speaker. Repeat the same for M10’s Left speaker terminals and

corresponding left speaker.

IDENTIFICATION OF CONTROLS

REAR VIEW

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M10 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info