Bedienungsanleitung NAD T 187 (Seite 44 von 48) (Englisch)

493498

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

The T 187 has the capability to operate via Alternate IR channel. This is

practically useful if you have two NAD products that can be operated by

similar remote control commands. With alternate IR Channel, two dierent

NAD products can be controlled independently in the same zone by

setting each one to a dierent IR channel.

IR CHANNEL ASSIGNMENT

The T 187 and the HTR 8 remote control must be set to the same channel.

To change the Main Zone IR Channel on the T 187

• Press and hold [ a SOURCE ] and then toggle STANDBY button to select

desired IR Channel – the VFD will show “IR Channel 1” or “IR Channel 0”.

The default IR Channel is “IR Channel 0”.

To change the IR Channel on the HTR 8 remote control

• Include a channel number before the library code. For HTR 8, library

code “100” is the default library table for “AMP” device. To select this

“AMP” library table for “IR Channel 0”, retain the library code “100” .

• If you want to load the “AMP” library table on “IR Channel 1”, prex the

library code with “1” to indicate association with “IR Channel 1”. Load

then the “AMP” library table using the code “1100”.

SAMPLE SETUP OF TWO NAD PRODUCTS ON THE SAME ZONE

NAD T 187 and NAD C 326BEE are both defaulted to IR Channel 0. If [OFF]

button is pressed on the HTR 8 remote control (or SR 8 remote control for

the C 326BEE), both products will go to standby mode. Press [ON] and both

products will power up from standby mode.

To prevent both products from simultaneously going in and out of standby

mode along with other common commands, set each one to a dierent

IR channel. In this setup, we will keep C 326BEE and SR 8 remote control

defaulted to “IR Channel 0”. As for T 187, we will assign it to “IR Channel 1”;

the same applies to HTR 8.

Set T 187 and HTR 8 to “IR Channel 1” via the following procedure.

T 187

• Press and hold [ a SOURCE ] and then toggle STANDBY button to

select “IR Channel 1”.

HTR 8

Begin by ensuring that the T 187 is powered-up (“on”, not merely in

standby).

• To enter HTR 8’s library mode, press and hold both the [AMP] device

and [A/V PSET] until the LEARN LED turns green.

• While keeping the HTR 8 pointed towards the T 187, enter the

library code “1100”. Press [OFF]. If the T 187 goes to standby mode,

press [ENTER] to accept the library code number and exit library

mode.

With both T 187 and HTR 8 set to “IR Channel 1”, the C 326BEE can now be

remotely controlled independent of the T 187.

NOTE

Performing a Factory Reset for T 187 or HTR 8 will result to a return to the

factorydefault“IRChannel0”setting.

OPERATION

USING IR CHANNEL

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD T 187 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 187

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info