707510
40
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
E38
40.1 General Connections Notes
The negative input and output connections are all
common. The mains earth should always be connected
regardless of what other equipment is used. This only
grounds the case and the electrostatic screen within the
transformer, and is not connected to the signal negative.
In order to avoid hum loops, the signal negative of the
whole system should be connected to the mains earth
(ground) in one place.
40.2 Protection Notes
If the amplifier’s external case reaches 70°C due to
prolonged running at high power, the mains supply will be
interrupted and the illuminated logo will switch off until
the amplifier has cooled down. This may take up to thirty
minutes.
40 Installation and Operation
The NAPV 145 is a mono power amplifier intended for use in audio-visual systems. The
NAPV 145 should be installed on a dedicated equipment stand intended for the purpose
and should be in its final location before connecting cables or switching on. Switch on the
source and preamplifier components, with the volume turned down, before switching on
the NAPV 145. The NAPV 145 power button is located on the front panel.
The NAPV 145 is heavy and care should be taken when lifting or moving it. Make sure that
the surface it is to be placed on can support the full weight.
OPERATION OF THE AMPLIFIER’S THERMAL PROTECTION
SUGGESTS PROLONGED USE AT TOO HIGH A VOLUME LEVEL.
YOUR LOUDSPEAKERS MAY BE AT RISK IF THIS IS THE CASE.
THE VOLUME SHOULD BE REDUCED.
40.3 Loudspeaker Cable and Connectors
Only Naim Audio speaker cable should be used to
connect a loudspeaker to the output of the NAPV 145.
Custom Naim Audio loudspeaker connectors are supplied
to make the connection and in order to comply with
current European safety regulations these should always
be used.
DAMAGE TO THE AMPLIFIER MAY RESULT IF “HIGH
DEFINITION” CABLE OR ANY OTHER SPECIAL CABLE IS USED
TO CONNECT THE LOUDSPEAKERS.
Ensure when connecting speakers that they are “in
phase”. That is, the positive and negative connection
orientation at both the speaker and amplifier ends of the
cable is the same for both channels.
mains input
and fuse
signal input
NAPV 145 Power Amplifier
42 NAPV 145 Specification
Power Output: 80 Watts, 8Ω
400 VA Transient
Quiescent Consumption:
15VA
Voltage Gain:
+29dB
Input Impedance:
18kΩ
Frequency Response: -3dB @ 2Hz and 65kHz
Dimensions (H x W x D): 87 x 432 x 314mm
Weight 15.8kg
Mains Supply: 100-120V or 220-240V, 50/60Hz
speaker
41 NAPV 145 Connections
41.1 NAPV 145 Rear
nc
-ve
i/p
Input
40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Naim NAP 500 DR wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Naim NAP 500 DR

Naim NAP 500 DR Bedienungsanleitung - Deutsch - 44 seiten

Naim NAP 500 DR Bedienungsanleitung - Deutsch - 16 seiten

Naim NAP 500 DR Bedienungsanleitung - Englisch - 16 seiten

Naim NAP 500 DR Bedienungsanleitung - Holländisch - 16 seiten

Naim NAP 500 DR Bedienungsanleitung - Französisch - 44 seiten

Naim NAP 500 DR Bedienungsanleitung - Französisch - 16 seiten

Naim NAP 500 DR Bedienungsanleitung - Italienisch - 46 seiten

Naim NAP 500 DR Bedienungsanleitung - Italienisch - 16 seiten

Naim NAP 500 DR Bedienungsanleitung - Spanisch - 16 seiten

Naim NAP 500 DR Bedienungsanleitung - Polnisch - 16 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info