Bedienungsanleitung Navman Depth 2100 (Seite 4 von 12) (Englisch)

512550

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

DEPTH 2100 Installation and Operation Manual

NAVMAN

Whenever power is applied the depth sounder is

active and water depth is displayed. If the sonar signal

does not show a bottom the display will indicate “- -”.

This can occur if the water is aerated or the maximum

depth is exceeded. Note: The maximum depth

decreases as boat speed increases.

Alarms

Two types of alarms can be set; the Deep Alarm and

the Shallow Alarm. The Deep Alarm can be set as

high as 184 metres (605 feet) while the Shallow

Alarm can be set as low as 0.3 metre (1 foot).

Whenever the water depth is greater than the Deep

Alarm setting and the alarm is enabled an alarm will

sound. The alarm repeats two short beeps and

alternates DAL and the water depth on the display.

Whenever the water depth is less than the Shallow

Alarm setting and the alarm is enabled an alarm will

sound. The alarm repeats a single long beep and

alternates SAL and the water depth on the display.

Alarms On/Off

Alarm settings are saved in memory.

To turn the alarm on, press (ON). An arrow on the

lower right corner of the display will show (next to the

Alarm Bell), to indicate that the alarms are on.

120

OFF

To turn the alarms off, press (OFF). The arrow in

the lower right corner will extinguish.

120

OFF

Note: The arrow will flash if alarms are turned ON

but the shallow alarm is individually set to OFF.

See next section.

3. Use

and to change the value. If either

key is held depressed for more than one

second the reading will increase or decrease

rapidly.

4. When the alarm is set, exit by pressing both

Shallow Alarm

To set the shallow alarm:

1. Press

for three seconds. The display will

show:

SAL

OFF

2. After a few seconds the

display will indicate the current

Shallow Alarm depth setting.

Press for

3 Seconds

1 Operation

850

Press for 3

Seconds

851

and simultaneously. Alternatively, if no

keys are pressed for a period of 5 seconds the

normal depth display will resume.

OFFON

Press simultaneously to exit

Note: If the reading is decreased to below

1.5 feet (or equivalent) the display will

show OFF and the alarm will be disabled. The

alarm can also be disabled by pressing both

and for 5 seconds. The word OFF will be

displayed but the alarm depth will be retained for

future use.

Deep Alarm

To set the deep alarm:

1. Press for three seconds. The display will

show:

dAL

OFF

2. After two seconds the display

will indicate the current Deep

Alarm depth setting.

3. Use

and to change the

value. If either key is held depressed for more

than one second the reading will increase or

decrease rapidly.

4. When the alarm is set, exit by pressing both

and simultaneously. Alternatively, if no keys

are pressed for a period of 5 seconds the

normal depth display will resume.

OFFON

Press simultaneously to exit

Note: If the reading is increased one step above

600 feet (or equivalent) the display will

show OFF and the alarm will be disabled. The

alarm can also be disabled by pressing both

and for 5 seconds. The word OFF will be

displayed but the alarm depth will be retained for

future use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman Depth 2100 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman Depth 2100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info