Bedienungsanleitung Navman Depth 2100 (Seite 5 von 12) (Englisch)

512550

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

DEPTH 2100 Installation and Operation Manual

NAVMAN

Keel/Surface Offset

An offset may be automatically added to or subtracted

from the depth reading to compensate for the location

of the transducer. This allows the instrument to

indicate the water depth relative to the bottom of the

keel or the surface of the water.

To set the keel/surface offset:

1. Apply power while holding down .

OFF

Hold down during power up

2. When the unit is on, release . The display will

indicate if the current offset is keel offset or

waterline offset:

Hull Offset (Depth below the keel)

Surface Offset (Depth below the surface)

3. After 5 seconds the display will indicate the

current offset.

Note: A negative offset is used to display depth

below the keel and a positive offset is used to

display depth below the surface.

8. To exit this mode, press and hold both

and

2 Instrument Setup

4. Use and to change the value. If either key

is held depressed for more than one second the

reading will increase or decrease rapidly.

5. The offset can be programmed in 0.1 unit steps

from -9.9 to 9.9 feet (or equivalent). When

programmed for a negative offset, ‘-’ will be

indicated on the left hand side of the display.

6. To display depth below the keel enter the

vertical distance between the bottom of the keel

and the depth transducer as a negative value.

7. To display depth below surface enter the

vertical distance from the waterline to the

depth transducer as a positive number (no

negative sign).

Hold down

during power up

simultaneously. Alternatively, if no keys are

pressed for a period of 5 seconds normal depth

display will resume.

OFFON

Press simultaneously

The display will now indicate the current water

depth.

Transducer Setting

A Transducer Setting is provided to allow the Depth

2100 to be used with different transducer types. The

default setting (= 0.0) is used for most transducers.

Some transducers ‘ring’ after the sonar transmit pulse

(just like hitting a bell). This ringing can be interpreted

as an echo from a shallow bottom. The setting is

used to increase the required level that shallow

echoes must meet before they will be displayed.

If the Depth 2100 gives repeated false readings of

1.5 to 3 feet depth while in deep water the transducer

setting should be increased. Adjust it upward by 0.5

at a time and retest. The range of values is -0.9 to

+2.5. If the value is set too high it could cause erratic

readings in shallow water.

Changing the Transducer Setting:

1. Apply power while holding down

. The

display will show either HOF or SOF for 7

seconds. Continue to hold the key down.

2. The display will show tdr.

tdr

3. Release the key.

4. After 2 seconds the display will show the

Transducer Setting value eg 0.0.

5. Use and to change the value.

6. To exit this mode, press and hold both

and

simultaneously.

Units of Measure

To select the displayed unit

1. Apply power while holding down

OFF

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Navman Depth 2100 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Navman Depth 2100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info