Bedienungsanleitung Novy 1801 One Power (Seite 22 von 24) (Deutsch, Englisch, Holländisch, Französisch)

741773

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

EN 22

3.2 Exhaust duct to the outside

The motor outlet has a rectangular exhaust of 220 x 90 mm. It is recommended to connect an exhaust duct to this with

the same dimensions (drawing 8).

For optimum performance of the hood it is important to pay attention to the items mentioned below.

When using a ﬂat exhaust duct:

• Use ﬂat ducts with rounded corners and air conductors in the bends. These ducts are to be obtained through Novy.

• An adapter makes it possible to change from a ﬂat to a round exhaust duct.

When using a round exhaust duct:

• Use smooth, non-ﬂammable pipes with an internal diameter that is equal to the external diameter of the connection

nozzle of the hood. Maximally extend ﬂexible ducts and cut them to size.

• Do not reduce the exhaust diameter. This will decrease the capacity and increase the noise level.

• When connecting to a short exhaust duct, it may be required to mount a non-return valve to prevent the wind from

blowing in.

• Use a hose clamp or aluminium tape for airtight connections.

• In case of an exhaust pipe through the outside wall, use the outside wall grate.

General:

• Make the duct as short as possible and with as few as possible bends to the outside.

• Avoid square bends. Use rounded bends for proper air conduction.

• If an exhaust pipe through the outside wall passes a cavity wall, make sure that the exhaust duct fully bridges the

cavity and slightly declines to the outside.

• In case of an exhaust pipe through the roof, use a double-walled roof passage with sufﬁcient width.

• Never connect the exhaust to a ﬂue duct.

• Make sure that sufﬁcient air is supplied. Fresh air can be supplied by slightly opening a window or an outside door or

by installing an inlet grate.

The unit is by default set to recirculation. Disable the recirculation program in case of exhaust to the outside (5.2).

4. ELECTRICAL CONNECTION

The installation and connection to the electricity grid shall only be carried out by an expert (electrician) who is

familiar with the required standards.

The junction box is to be found at the bottom of the cooking plate. Use a screwdriver to open the cover and place this in

the 2 grooves before the arrows.

Disable the main switch of the fuse concerned before connecting the unit.

Connect the unit in accordance with the table and diagram below.

Mains Connection Supply cord Circuit braker Wiring diagram

230V 50/60Hz 1 phase + N 3 x 6 mm² 32 A

230V 50/60Hz 3 phases 4 x 6 mm² 20 A

400V 50/60 Hz 2 phases + N 4 x 4 mm² 16 A

400V 50/60 Hz 3 phases + N 5 x 4 mm² 16 A

Attention! Properly put through the wires and tighten the screws.

We will not accept any responsibility for accidents resulting from a poor or wrong connection or accidents that may occur

with units without or with a defective earthing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Novy 1801 One Power Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Novy 1801 One Power

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info