Bedienungsanleitung Novy 1801 One Power (Seite 23 von 24) (Deutsch, Englisch, Holländisch, Französisch)

741773

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

5. COMMISSIONING

5.1 Mount the glass plate onto the tower

Press 2 sec. on key

to move the tower up. Take the tower assembly from the cooking plate by pulling it up and place

the tower on the table top. Take the loose glass plate and place it with a turning movement onto the tower (drawing 9

and 10).

5.2 User modes

The unit is by default set for operation in the recirculation mode. If an exhaust to the outside is used anyway, disable the

indicator for saturated recirculation ﬁlter as follows:

CHANGE SETTING FOR EXHAUST DUCT TO THE OUTSIDE:

Only disable the programming when mounting an exhaust duct to the outside.

This setting can only be changed when the tower has been disabled and therefore is in the most downward position.

Simultaneously press the key combination [

], [ ], [ ] for 3 seconds until the LED beside the blinks 3 times

SETTING BACK TO RECIRCULATION:

Simultaneously press the key combination [

], [ ], [ ]for 3 seconds until the LED beside the lights up for 3

seconds

5.3 Limitation maximum power induction hob (only for 1801 One Power)

The hob can be equipped with a power limitation. If you reach the maximum power it will be impossible to increase the

power on the different cooking zones and a beep signal will sound. This limitation is set at 7400W (32A) by the factory but

it is possible to change it to 4800W (20A) or 3000W (12A).

Before beginning the procedure:

• Make sure there is no more pot on the hob

• Disconnect the appliance from the grid by removing the fuse or turning the circuit breaker off.

• Reconnect the table to the grid

• Start the procedure within 2 minutes after reconnecting the hob to the grid

• Make sure all cooking zones are off.

Procedure:

1) Press simultaneously on both zone selection keys of the

bottom zones during 3 seconds. A beep will sound and the

current power is displayed.

2) To set the power limitation use the [ + ] and [ - ]. To exit the

procedure without saving your changes, don’t touch any

key for 60 seconds.

3) To save the new power limitation, press simultaneously

on both zone selection keys of the bottom zones during

3 seconds. Once the new limitation registered, a beep will

sound.

6. ACCESSOIRIES

The following accessories can be ordered with the unit:

• Wall passage for ﬂat duct. Inox/SS incl. non-return valve:

article 906407

• Outside wall grate round duct Ø 150 mm. Aluminium shutter

grate: article 906178

• Non-return valve round duct Ø 150 mm: article 906269

• Aluminium tape, roll 50 metres: article 906292

OPTIONAL (1801 One Power & 1811 One Pro from v13)

Installation I/O module n° 990034

Open the cover of the electrical connection box.

Plug in the I/O module connection cable into the connector.

(See manual 990034 I/O module)

EN 23

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Novy 1801 One Power Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Novy 1801 One Power

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info