Bedienungsanleitung Numark 200FX (Seite 3 von 22) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

23412

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

MIXER QUICK SETUP

1. Make sure all items listed on the front of

this guide are included in the box.

2. READ SAFETY INSTRUCTION BOOKLET

BEFORE USING THE PRODUCT.

3. Study this setup diagram.

4. Place mixer in an appropriate position for

operation.

5. Make sure all devices are turned off and all

faders and gain knobs are set to “zero”

6. Connect all stereo input sources as

indicated in the diagram.

7. Connect the stereo outputs to power

amplifier(s), tape decks, and/or other audio

sources.

8. Plug all devices into AC power.

9. Switch everything on in the following order.

• audio input sources (i.e. turntables or

CD players)

• mixer

• last, any amplifiers or output devices

10. When turning off, always reverse this

operation by,

• turning off amplifiers

• mixer

• last, any input devices

11. Go to http://www.numark.com for product

registration.

More information about this product may be

found at http://www.numark.com

222

3131333

67899

REAR CONNECTIONS

1. Phono Inputs: This input is used for

connecting your turntables through the

sensitive RIAA phono preamplifiers. Only

turntables with phono level output should be

attached. Line level turntables must be

attached to the line inputs.

2. GND: This screw connector should be used

to secure any turntables or other devices

connected to the mixer that need to be

grounded.

3. Line Inputs: CD players, Tape Decks,

Samplers or other line level input devices

should be connected to these inputs.

4. Microphone Input: Microphones with a ¼”

connector can be connected to these input

terminals.

5. Fader Start Connector: to attach your

mixer to a remote start equipped Numark CD

player using industry standard 1/8”(3.5mm)

cables.

6. Zone Output (RCA): This output is for

connecting an external monitoring device

such as a PA system, powered monitors or a

home stereo. The level of the zone stereo

output signal is controlled by the zone fader.

7. Record Output: This RCA output is for

connecting a recording device such as a tape

deck or CD recorder. The level of the record

output is based upon pre-master levels.

8. Master Output (RCA): This output is for

connecting an external monitoring device

such as a PA system, powered monitors or a

home stereo. The level fo the master stereo

out put signal is controlled by the master

fader.

9. Stereo Balanced Master Outputs (XLR):

low-impedance XLR type connectors

controlled by the Master fader.

10. AC In: This mixer is designed to work with

the power supply cord that comes with the

unit. While the power is switched off, plug

the power supply into the mixer first, then

plug it into the outlet.

11. Voltage Selector: Set this to the correct

voltage for your location standard.

12. Power Switch: Use this switch to turn on

the mixer after all input devices are already

connected to prevent damage to your

equipment. Turn the mixer on before you

turn on amplifiers and turn of amplifiers

before you turn off the mixer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Numark 200FX Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info