Bedienungsanleitung Numark 200FX (Seite 4 von 22) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

23412

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

19 18 19 2020 1415 17

23 26

2125

29 29

FRONT PANEL FEATURES

1. Power LED: Illuminates when the mixer is on.

2. Mic ON/OFF: Toggles activation of the DJ Mic.

3. Mic Gain: This knob adjusts the volume of the

microphone input.

4. Mic Bass: This knob adjusts the low-tone of the

microphone.

5. Mic Treble: This knob adjusts the high-tone of

the microphone.

6. XLR/¼” Combo Microphone Input Jack:

Connect your DJ mic at this location.

7. Channel Gain: This rotary control adjusts the

pre-fader input level.

8. Channel Treble: This rotary control adjusts the

high-tone level.

9. Channel Middle: This rotary control adjusts the

middle-tone level.

10. Channel Bass: This rotary control adjusts the

low-tone level.

11. Input Selector: This toggles select what input

source is routed to the channel from the rear

panel connected units.

12. Channel Fader: This slide fader is used to

adjust the level sent to program mix.

13. Cue Button: pressing this button sends post

gain, post EQ, and pre channel fader level audio

the PFL “Pre–fader level” section of the

headphone cue.

14. Headphone Volume: This rotary control

adjusts the volume level of the headphone

output.

15. Headphone Mix: Program level and PFL (CUE)

signal levels can be mixed by this slider. When

all the way left, audio heard will be determined

by Cue Button selections. When all the way

right final only (PGM) program mix audio will be

heard.

16. Split/Blend Button: When in the down

position, headphone audio will be split so mono

PFL audio is in the left ear and mono PGM audio

is in the right ear. When the button is up,

stereo PFL and PGM audio will be mixed

(blended).

17. Headphone Jack: Your headphones can be

connected to this ¼” terminal. The volume

should always be set at its lowest setting while

connecting and disconnecting headphones to

prevent damage to headphones and/or your

hearing.

18. Replaceable Crossfader: This slide fader

blends audio between the channels assigned to

the left and right assign switches.

Note: This fader is user replaceable if it should

ever wear out. Simply remove the facepanel and

then remove the screws holding it in position.

Replace the fader with a quality authorized

replacement from your local Numark retailer.

19. Assign Knob: Rotary position determines

which input channel will be heard when the

crossfader is moved towards this knob.

Volume levels of channels not selected will be

determined only by the individual channel

sliders.

20. Fader Start: Activates the crossfader to send

play and cue digital pulse commands to your

auto-start Numark CD player or other popular

brand. For fader start, attach your mixer to a

remote start CD player using industry standard

1/8”(3.5mm) cables. When you move the

crossfader toward the active channel, the

attached CD player will start. When it is

moved away, that side will cue (similar to

pressing the cue button) or stop depending

upon brand of CD player.

21. Master Slider: This control adjusts the main

output volume using the PROGRAM audio as a

source.

22. Stereo/Mono toggle: Adjusts the Master

output for stereo or mono operation.

23. Panning: Adjusts the balance of right to left

audio in all outputs (Master, Record, Zone).

24. Meter Assign: Determines whether PFL or

post master level audio is sent to the stereo

LED meter.

25. Stereo Level Indicator: Quickly and

accurately tracks level of audio sent to it.

When using as a master output meter, set

the crossover, equalizer and power amp inputs

to avoid distortion at each step in the audio

chain. Proper attention to the peak meter

results in the punchiest possible sound without

audible distortion. When used to adjust the

PFL levels, PFL cue signal is sent to the meter

through the cue assign buttons. Accurately

match channel levels with the Pre-fader gain

and EQ controls before mixing them together.

The idea is to properly match PFL inputs

, not

the input with the stereo output meter!

26. Booth/Zone Fader: Controls volume for a

remote zone or booth monitors using

PROGRAM audio as a source.

NOTE: This could also be used to supply line

level audio to a lighting controller or to lights

that are sound activated.

27. Effects ON/OFF: Toggles activation of Digital

Effects.

28. Blend Control Knob: Rotary position

determines amount of effect added to selected

channel(s).

29. Effects Assign Button: Determines what

channel(s) the effects are added to.

30. Effects Selector: Rotary position

determines what type of effect is assigned to

selected channel(s).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Numark 200FX Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info