Bedienungsanleitung Oceanic OCS (Seite 55 von 62) (Englisch)

551851

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

OCS OPERATING MANUAL

CARE AND CLEANING

Protect your OCS from shock, excessive temperatures, exposure to chemicals, and tampering. Protect the lens against scratches

with a Instrument Lens Protector. Small scratches will naturally disappear underwater.

• Soak and rinse the OCS in fresh water at the end of each day of diving, and check to ensure that the areas around the Low

Pressure (Depth) Sensor (Fig. 164a), PC Interface Data Port (Fig. 164b), and Buttons are free of debris or obstructions.

• To dissolve salt crystals, use lukewarm water or a slightly acidic bath (50% white vinegar/50% fresh water). After removal

from the bath, place the OCS under gently running fresh water and towel dry before storing.

• Transport your OCS cool, dry, and protected.

INSPECTIONS AND SERVICE

Your OCS should be inspected annually by an Authorized Oceanic Dealer who will perform a factory prescribed function check

and inspection for damage or wear. To keep the 2 year limited warranty in effect, this inspection must be completed one year

after purchase (+/- 30 days).

Oceanic recommends that you continue to have an inspection performed every year to ensure it is working properly. The costs of

annual inspections, or inspections relating to water tight integrity, are not covered under the terms of the 2 year limited warranty.

To Obtain Service:

Take your OCS to an Authorized Oceanic Dealer or send it to the nearest Oceanic Regional Facility.

To return your OCS to Oceanic:

• Record all dive data in the Log and/or download the data stored in memory. All data will be erased during factory service.

• Package it using a protective cushioning material.

• Include a legible note stating the speciﬁc reason for return, your name, address, daytime phone number, serial number(s),

and a copy of your original sales receipt and Warranty Registration Card.

• Send freight prepaid and insured using a traceable method to the nearest Oceanic Regional Facility, or to Oceanic USA.

• If shipping to Oceanic USA, obtain an RA (Return Authorization) number by contacting Oceanic at 510/562-0500 or send

an e-mail to service@oceanicusa.com.

• Non-warranty service must be prepaid. COD is not accepted.

• Additional information is available at the Oceanic web site OceanicWorldwide.com

BATTERY REPLACEMENT

CAUTION: The procedures that follow must be closely adhered to avoid entrance of water into the

unit. Damage due to improper Battery replacement (or subsequent leakage of moisture into the unit)

is not covered by the OCS's 2 year warranty.

NOTE: The OCS can be sent to Oceanic Worldwide, Regional Distributor, or Authorized Dealer Service

for proper battery change service which includes pressure (depth) and leak testing to the max operat-

ing depth. Standard charges for service will apply

The Battery Compartment should only be opened in a dry and clean environment with extreme care taken to prevent the entrance

of moisture or dust.

As an additional precautionary measure to prevent formation of moisture in the Battery Compartment, it is recommended that the

Battery be changed in an environment equivalent to the local outdoor temperature and humidity (e.g., do not change the Battery

in an air conditioned environment then take it outside during a hot sunny day).

Inspect the Buttons, Lens, and Housing to ensure they are not cracked or damaged. If there is any sign of moisture in the OCS,

DO NOT attempt to use it for diving (NORM, GAUG, or FREE) until it receives proper service by the Oceanic factory or an

Authorized Regional Distributor.

Data Retention

When the battery is removed, settings and nitrogen/oxygen calculations for repetitive dives will be retained in volatile memory

until a new battery is installed. You will have the choice of saving or deleting the data. The Compass will need to be calibrated

after the new battery is installed.

All parts needed for the battery change that follows are provided in the OCS Battery Kit available from your Oceanic Dealer.

Battery Removal

• There is no need to remove the straps.

• Remove the (4) retaining screws located on the back of the case (Fig. 165) by turning them counter clockwise with a small

ﬂat tip 3mm screw driver.

• Carefully separate the front and back sections. If necessary, insert a small ﬂat tip screw driver in the slot machined into the

Cover at the 11 o'clock position (Fig. 166A) and gently pry the Battery Cover loose, then lift it off the case (Fig. 166B).

• Turn the case to one side to drop the Battery into your hand. If necessary, gently loosen it with the tip of your ﬁnger (Fig.

167). DO NOT use tools to pry it out, or short the positive (+) top of the Battery to the negative ( - ) contact under it.

• Discard the Battery according to local regulations governing disposal of Lithium batteries.

Fig. 164 - FRONT

Fig. 165 - CASE BACK

Fig. 166B - LIFTING

BATTERY COVER OFF

Fig. 167 - BATTERY

REMOVAL

Fig. 166A - TO LOOSEN

BATTERY COVER

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oceanic OCS Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oceanic OCS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info