Bedienungsanleitung Oceanic OCS (Seite 56 von 62) (Englisch)

551851

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

OCS OPERATING MANUAL

Inspection

• Closely check all of the sealing surfaces for any signs of damage that might impair proper sealing.

• Inspect the buttons, lens, and housing to ensure they are not cracked or damaged.

WARNING: If damage or corrosion is found, return your OCS to an Authorized Oceanic Dealer, and

DO NOT attempt to use it until it has received factory prescribed service.

• Remove the cover O-ring by squeezing the sides (Fig. 168a). Discard, and do not attempt to reuse it.

> It is located around the top rim of the cover.

> DO NOT use tools to remove the O-ring.

> To ensure proper sealing, O-ring replacement is required each time the Battery is replaced.

Battery Installation

• Very lightly lubricate the new O-ring with silicone grease and place it on the top rim of the cover.

• Place a new 3 volt type CR2450 Lithium Battery, negative side down into the Battery cavity and ensure that it is evenly

positioned (Fig. 169).

• Carefully position the Battery Cover over the battery compartment. Use the OCS logo as a guide for top/bottom. Also,

small symbols have been engraved on the top of the Cover and strap to serve as a guide for proper alignment (Fig. 170a).

• While ensuring that the cover and back of the case are properly aligned, ﬁrmly press them evenly and completely together.

• While holding the Battery Cover ﬁrmly in position agaonst the back of the case (Fig. 171), insert the (4) retaining screws

and tighten them until secure by turning them clockwise with a small ﬂat tip 3mm screw driver. DO NOT over tighten.

Testing

> Activate the unit and ensure that the LCD is clear and sharp in contrast. If any portions are missing or appear dim, or if a

Low Battery condition is indicated, return the OCS to an Authorized Oceanic Dealer for evaluation before use.

> During 24 hours after completion of a dive, the graphic DATA with selections SAVE ? and CLEAR ? will be displayed (Fig.

172) giving you the option to retain or delete Ni-O2 calculations for repetitive dives.

• A (< 2 sec) to toggle between SAVE and CLEAR

• S (< 2 sec) to save the selection

> Graphics DATA SAVED (or CLEARED) with CAL COMPASS appear for 3 seconds (Fig. 173), then operation reverts to the

Compass CAL screen.

> Calibrate the Compass.

> Verify all Set Points prior to diving.

Fig. 168 - SQUEEZING

COVER O-RING

Fig. 169 - INSTALLING

BATTERY

Fig. 170 - BATTERY COVER

ALIGNMENT

Fig. 171 - PRESSING

FRONT & BACK TOGETHER

Fig. 172 - SELECT

Fig. 173 - DATA SAVED

ALTITUDE SENSING AND ADJUSTMENT

Prior to the ﬁrst dive of a series of repetitive dives, Altitude (i.e., ambient pressure) is measured upon activation of Dive Surface

Mode and every 15 minutes until a dive is made or operation reverts to Watch Mode.

> While it is operating in Watch modes after a dive, measurements are taken every 15 minutes during the 24 hour period

after surfacing.

> Measurements are only taken when the unit is dry.

> Two readings are taken, the second reading 5 seconds after the ﬁrst. The readings must be within 1 foot (30 cm) of each

other to record that ambient pressure as the current Altitude.

> No adjustments are made during any time that the Wet Contacts are bridged.

When diving in high altitude waters from 3,001 to 14,000 feet (916 to 4,270 meters), the OCS automatically adjusts to these

conditions providing corrected Depth, and reduced No Deco and O2 Times at intervals of 1,000 feet (305 meters).

At an elevation of 3,001 feet (916 meters), Depth calibration automatically changes from feet of seawater to feet of fresh water.

This is the ﬁrst adjustment to the algorithm.

When the Conservative Factor feature is set On, NDLs are calculated based upon the next higher 3,000 foot (915 meter) Alti-

tude. All adjustments for Altitudes greater than 11,000 feet (3,355 meters) are then made to allowable dive times for 14,000

feet (4,270 meters). At Sea Level, calculations are based upon an Altitude of 6,000 feet.

The OCS will not function as a Dive Computer above 14,000 feet (4,270 meters).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oceanic OCS Seite 56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oceanic OCS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info