492763
21
Zoom out
Zoom in
Vorherige Seite
1/22
Nächste Seite
TROUBLESHOOTING (cont.)
Problem: Solution
The Home Producer
8 does not operate
your home
entertainment
component?
The
Home
Producer 8
is not
performing
commands properly?
You make a mistake
when setting up your
Home Producer 8
?
display screen will change to
[SEL TO RS]. Press
SELECT. The display
screen will then return to
[TV and the TIME].
Try all of the codes listed for
your brand of home
entertainment component
in the “Set-Up Codes”
section. If this does not
work, try searching for your
code. Make sure the home
entertainment component
you are setting up is able
to be operated with an
infrared remote control.
Try all of the codes listed for
your brand of home
entertainment component
in the “Set-Up Codes”
section. Many set-up codes
may allow some degree
of operation. However, only
one set-up code will work
correctly with your home
entertainment component.
During any set up procedure,
except for Macros and Timed
Sequences, the ESC key will
return you to the
[DEVICE and the TIME]
screen without saving. If you
make a mistake when setting
up a Timed Sequence, return
to the Timed Sequence
menu and delete the
incorrect sequence. If you
make a mistake when saving
a macro, erase the incorrect
macro by re-saving a new
macro on the same key.
TROUBLESHOOTING
Problem: Solution
LCD screen begins
to fade, does not
appear or the red
light blinks five times
when you press a
key?
[MEM FAULT]
appears on the LCD
screen.
Replace the batteries with
four (4) new AAA alkaline
batteries. Immediately
before removing the
batteries, please refer to
page 8 and re-enter your
TV’s setup code. This will
allow the
Home Producer 8
to retain its memory upon
removing the batteries. If
you do not, upon entering
your fresh batteries, the LCD
screen may say
[MEM FAULT].
If [MEM FAULT] does
appear on the LCD screen,
press and hold MAGIC
until the display screen
changes from [TV and the
TIME] to [TIMED SEQ].
Press the MENU - key one
time. The display screen will
change to [CODE SET UP].
Press SELECT. The display
will change to
[DEV SET UP]. Press
SELECT and the display
screen will change to [TV].
Enter code 9-6-1. Press
SELECT, then ESC. Now
press and hold MAGIC until
the display screen changes
from [TV and the TIME] to
[TIMED SEQ]. Press the
MENU + key one time. The
display screen will change to
[CONFIGURE]. Press
SELECT. The display
screen will change to
[THEATR SEL]. Press
MENU + once. The display
screen will change to
[SERVICE]. Press SELECT.
The display screen will
change to [MFG RESET].
Press SELECT. The
21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für One for All URC 8090 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info