Bedienungsanleitung Parkside PDEXS 150 A1 - IAN 73789 (Seite 33 von 37) (Deutsch, Englisch, Holländisch)

668299

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

33 GB

Safety instructions Safety instructions / Before use

Additional safety instructions

for pneumatic machinery

Compressed air can result in serious

injuries.

Always close the air supply, release pressure

from the hose, and disconnect the machine from

the compressed air supply, when the machine

is not in use, before switching accessories or

when performing repairs.

Never aim the air flow at yourself or

others.

Hoses flapping about can result in

serious injuries. Therefore, always inspect

hoses and their fasteners for damage and a

secure fit.

If using universal swivel couplings (coupling

discs) always use locking pins. Whip-check

hose safety cables must be used for protection

in the event the connection between the hose

and the machine or in between hoses fails.

Ensure not to exceed the maximum

pressure specified on the machine.

Never carry pneumatic tools by the

hose.

Original accessories / tools

Use only the accessories detailed in the

operating instructions. The use of inserted

tools or accessories other than those recom-

mended in the operating instructions could lead

to you suﬀering an injury.

Before use

Selecting the grinding disc

Metal Removal and Surface:

The rate of metal removal and the surface quality

are determined by the grain size of the grinding disc.

lease note that corresponding grinding discs

with diﬀerent grain sizes should be used for

processing diﬀerent materials.

Changing sanding sheets

The air sander is ﬁtted with a hook and loop fastening,

which allows for quick and easy replacement of

sanding discs.

Lift the grinding disc at the side and pull it oﬀ

from the backing pad

in order to remove it.

Note: Before securing a new sanding sheet, re-

move all dust and dirt from the sander plate

Ensure that the openings in the sanding sheet

concur with the boreholes of the sanding plate

Dust / swarf removal by suction

Please note the “Safety instructions” section.

Using the internal vacuum extraction

with dust collection device (see Fig. B):

Push the exhaust air hose

fully on to the

connection for dust extraction

. Put the open-

ing of the dust bag

over the free end of the

exhaust air hose

and fasten the dust bag

ﬁrmly in position.

Note: Empty the dust bag

in good time and

regularly to ensure optimum dust extraction. To

do this open the zip fastener on the underside

of the dust bag

Topping up the oil

In order for the air sander to have a long service life,

there must always be enough pneumatic oil in the

device.

You may ensure this in any of the

following ways:

Connect a service unit with an oiler to the

compressor.

Install a line oiler in the compressed air line or

at the compressed air device.

Put approx. 3–5 drops of pneumatic oil by

hand into the plug nipple

every 15 minutes

of operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PDEXS 150 A1 - IAN 73789 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info