Bedienungsanleitung Parkside PDEXS 150 A1 - IAN 73789 (Seite 34 von 37) (Deutsch, Englisch, Holländisch)

668299

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

34 GB

Service centre / Warranty / Disposal Preparing for use / Advice on use / Cleaning

Preparing for use

Connecting the compressed

air source

Note: The air sander must be operated using

cleaned and condensate-free compressed air only

and its maximum allowable working

pressure of

6.3 bar at the device must not be exceed

ed.

Note: The compressed air source must be ﬁtted

with

a (ﬁlter) pressure reducer so that the air pressure can

be regulated.

Connect the plug nipple

by a quick-release

coupler to the compressed air supply.

Switching on and oﬀ

Note: Always switch on the air sander before

bringing it into contact with the workpiece material.

Switching on the air sander:

Press the operator’s lever

fully down

(see Fig. C).

Set the speed using the speed control

Switching off the air sander:

Release the operator’s lever

After you ﬁnish work, disconnect the device

from the compressed air source.

Note: First disconnect the hose from the com-

pressed air source (compressor) and only then

disconnect the compressed air supply hose

from the device. This will ensure that the com-

pressed air supply hose does not wave around

in an uncontrolled manner.

Advice on use

Wait until the device has come to a standstill

before you put it down.

Sanding surfaces

Switch the air sander on and bring the whole

of its sanding area into contact with the surface

to be abraded. Move it using even pressure to

and fro over the workpiece (see Fig. D).

Note: The sanding output and appearance are

largely dependent on the choice of sanding

sheet and the pressure applied. A sanding sheet

must be free of defects to produce a good

sanding output.

Ensure that you use an even pressure. Excessive

pressure does not produce a higher sanding out-

put, it just increases the wear on the sanding

sheet.

A sanding sheet previously used on metal must

not be used on other materials.

Replacing the backing plate

RISK OF INJURY! Always

disconnect the device from the compressed air

source before you replace the backing plate

Push the open-ended spanner

between the

backing plate

and collar

Release the backing plate

by turning the

plate anticlockwise and holding the open-ended

spanner

still against this movement.

Screw on a new backing plate

clockwise

until tight while holding the open-ended span-

ner

still against this movement.

Cleaning

RISK OF INJURY! Always

disconnect the device from the compressed air

source before you clean it.

Clean the air sander after you have ﬁnished

using it.

Store the air sander in dry enclosed rooms only.

Use a dry cloth to clean the device. Under no

circumstances should you use petrol, solvent or

cleaners which attack plastic.

Keep the ventilation openings clear at all times.

Remove dust clinging to the sander

with a brush.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PDEXS 150 A1 - IAN 73789 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info