Bedienungsanleitung Pioneer XDJ-AERO (Seite 33 von 37) (Englisch)

491973

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

Additional information

Troubleshooting

! Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points

below. Sometimes the trouble may lie in another component. Inspect the other components and electrical appliances being used. If the trouble

cannot be rectified after checking the items below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.

! This unit may not operate properly due to static electricity or other external influences. In this case, proper operation may be restored by turning the

power off, waiting 1 minute, then turning the power back on.

Power supply

Problem Check Remedy

The power is not turned on.

None of the indicators light.

Is the power cord properly connected? Plug in the power cord to an AC outlet. (page 10)

Is the [STANDBY/ON] switch for power supply

set to [ON]?

Set the [STANDBY/ON] switch for power supply to [ON]. (page 15)

The [STANDBY/ON] indicator flashes

and the power does not turn on.

— Normal operation can sometimes be restored by unplugging the power cord,

waiting at least 1 minute, then plugging the power cord back in.

If the symptom persists, unplug the power cord and request repairs.

Audio output

Problem Check Remedy

No sound or small sound. Are the [DECK1, PHONO1/LINE1] and [DECK2,

PHONO2/LINE2] selector switches set to the

proper positions?

Switch the channel’s input source using the [DECK1, PHONO1/LINE1] and

[DECK2, PHONO2/LINE2] selector switches. (Page 23)

Are the [TRIM] control, channel faders, crossfader

and [MASTER LEVEL] control set to the proper

positions?

Set the [TRIM] control, channel faders, crossfader and [MASTER LEVEL] control

to the proper positions. (Page 23)

Is the [LINE, PHONO] selector switch on this

unit’s rear panel properly set?

Properly set the [LINE, PHONO] selector switch on this unit’s rear panel accord-

ing to the connected device. (page 10)

Distorted sound. Is the [MASTER LEVEL] control set to the proper

position?

Adjust [MASTER LEVEL] so that the orange indicator on the master level indica-

tor lights at the peak level. (Page 23)

Is the [TRIM] control set to the proper position? Adjust [TRIM] so that the orange indicator on the channel level indicator lights

at the peak level. (Page 23)

Is the [LINE, PHONO] selector switch on this

unit’s rear panel properly set?

Properly set the [LINE, PHONO] selector switch on this unit’s rear panel accord-

ing to the connected device. (page 10)

Is the sound level input to the [MIC] terminal set to

an appropriate level?

Set the audio level input to the terminals to a suitable level for the connected

devices.

No sound is produced, or sound is

distorted or noisy.

Is this unit placed near a TV? Turn the TV’s power off or install this unit and TV away from each other.

Microphone sound is not output or

volume is low.

Are the [MIC ATT.] and [MIC LEVEL] controls set

to the proper positions?

Set the [MIC ATT.] and [MIC LEVEL] controls to the proper positions.

Sound is distorted when an analog

player is connected to this unit’s

[PHONO/LINE] terminals.

Or, lighting of the channel level

indicator does not change even when

the [TRIM] control is turned.

Have you connected an analog player with a built-

in phono equalizer?

For analog players with built-in phono equalizers, use with the [LINE, PHONO]

selector switch on this unit’s rear panel switched to [LINE]. (page 10)

If the analog player with built-in phono equalizer has a PHONO/LINE selector

switch, switch it to PHONO.

Is an audio interface for computers connected

between the analog player and this unit?

If the output of the audio interface for computers is line level, use with the [LINE,

PHONO] selector switch on this unit’s rear panel switched to [LINE]. (page 10)

If the analog player has a PHONO/LINE selector switch, switch it to PHONO.

Display

Problem Check Remedy

The playing address display is not

displayed in the remaining time mode.

— When playing files recorded in VBR, it may happen that the set cannot detect the

length of the track immediately and that some time is required for the playing

address display to appear.

The category is not displayed. Is the rekordbox (Mac/Windows) library informa-

tion stored on the USB device?

Use a device onto which the library information has been exported from rekord-

box (Mac/Windows).

Is the USB device write-protected? Cancel the USB device’s write-protection so that this unit can write on it.

Caching meter is not displayed. Are you playing a track from a USB device? The caching meter is not displayed when playing tracks from USB devices.

Is a track over 10 minutes in length loaded? The caching meter is not displayed when tracks over 10 minutes in length are

loaded.

Is a WAV file loaded? —

Nothing is displayed. Is the auto standby function activated? This unit is shipped with the auto standby function turned on. If you do not want

to use the auto standby function, set [AUTO STANDBY] to [OFF]. (page 27)

Additional information

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer XDJ-AERO Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer XDJ-AERO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info