ENGLISH
UU
UU
SS
SS
II
II
NN
NN
GG
GG
TT
TT
HH
HH
EE
EE
II
II
RR
RR
OO
OO
NN
NN
- Connect the iron (B2) to the one-piece plug proceeding as shown in the "Operation"
section.
- For steam-ironing, adjust the temperature of the iron by positioning the temperature-
control knob (Y) to COTTON-LINEN.
- Wait for 3 or 4 minutes until the push-button lamp (X) extinguishes to show that the sole-
plate of the iron has reached the required temperature.
- Press the steam-supply push-button (X) to enable the steam to come out. The steam flow
will stop when the push-button is released. When you first start to use the iron a few drops
of water may come out of the sole-plate mixed with the steam due to imperfect heat
stabilisation. It is therefore advisable to direct the first jet of steam onto a rag.
- In order to obtain a continuous jet of steam move the sliding switch (W1). The steam
will continue to come out even when the sliding switch is released. To stop the flow of
steam push the sliding switch backwards (W1).
Important Note
Never leave the iron unattended while it is on.
Only iron on surfaces that withstand heat and that allow the steam to permeate through
them.
GG
GG
EE
EE
NN
NN
EE
EE
RR
RR
AA
AA
LL
LL
MM
MM
AA
AA
II
II
NN
NN
TT
TT
EE
EE
NN
NN
AA
AA
NN
NN
CC
CC
EE
EE
Before carrying out any type of maintenance make sure that the power cable has been
disconnected from the mains plug.
After using the brushes it is advisable to allow the bristles to cool in their natural position
so as to avoid them getting deformed in any way.
Check the conditions of the gaskets located inside the one-piece plug (B2) periodically.
If necessary replace them with the appropriate spares. Also carry out the same check on
the gaskets for connecting the extension tubes (D) and the handle (A2).
To clean the outside of the appliance just use a damp cloth. Do not use solvents or
detergents as these might damage the plastic surface.
CC
CC
ll
ll
ee
ee
aa
aa
nn
nn
ii
ii
nn
nn
gg
gg
tt
tt
hh
hh
ee
ee
""
""
EE
EE
cc
cc
oo
oo
AA
AA
cc
cc
tt
tt
ii
ii
vv
vv
ee
ee
--
--
FF
FF
ii
ii
ll
ll
tt
tt
ee
ee
rr
rr
""
""
ww
ww
aa
aa
tt
tt
ee
ee
rr
rr
--
--
bb
bb
aa
aa
ss
ss
ee
ee
dd
dd
ff
ff
ii
ii
ll
ll
tt
tt
ee
ee
rr
rr
We strongly recommend cleaning the "Eco-Active Filter" water-based filter each time you use
it. Pull the lid of the accessory holder upwards as shown in Figure 2 so that it can be
unhooked. Lift up the water container (25) and remove it from its compartment by the handle
of the container (26) pushing the flap of the built-in socket (24) to one side as shown in Figure
3. Press the lever for opening the handle of the water container (27) and pull (Figure 4 ).
Remove the "EcoActiveFilter" water-based filter assembly (28).
Empty the sucked in material out of the water container (25).
Unhook the ring locking the tube elbow in place (32) by pulling it outwards (Figure 11).
Pull the tube elbow (33) from the body of the filter with the micro-holed net (31) until it
comes out. Take all the components to pieces and rinse them in running water (Figure 12).
Put the water-based filter assembly back together again repeating the operations described
above but in reverse order.
Put the filter assembly correctly back into place inside the tank.
