ENGLISH
CC
CC
ll
ll
ee
ee
aa
aa
nn
nn
ii
ii
nn
nn
gg
gg
oo
oo
rr
rr
rr
rr
ee
ee
pp
pp
ll
ll
aa
aa
cc
cc
ii
ii
nn
nn
gg
gg
tt
tt
hh
hh
ee
ee
ff
ff
ii
ii
ll
ll
tt
tt
ee
ee
rr
rr
ii
ii
nn
nn
gg
gg
ss
ss
pp
pp
oo
oo
nn
nn
gg
gg
ee
ee
Unhook the ring locking the tube elbow in place (32) by pulling it outwards (Figure 11).
Pull the tube elbow (33) out of the filter body with the micro-holed net (31) until it comes
right out. Take all the components to pieces and rinse them in running water (Figure 12).
(If the filtering sponge is torn replace it. Purchase a new one from an authorised Polti
assistance centre or call toll-free number).
RR
RR
ee
ee
pp
pp
ll
ll
aa
aa
cc
cc
ee
ee
mm
mm
ee
ee
nn
nn
tt
tt
oo
oo
ff
ff
tt
tt
hh
hh
ee
ee
HH
HH
EE
EE
PP
PP
AA
AA
ff
ff
ii
ii
ll
ll
tt
tt
ee
ee
rr
rr
cc
cc
aa
aa
rr
rr
tt
tt
rr
rr
ii
ii
dd
dd
gg
gg
ee
ee
Unhook the lever for opening the air-output screen (17) and
rotate it upwards (Figure 15). Turn the closure (34) towards
the outside in order to release the HEPA filter.
Pull the HEPA filter out of its seating and replace it with an
original Polti filter.
Note: The filter lasts for about 100 hours (approximately 6
months) when used normally in a domestic
environment. If the force of suction drops
considerably replace the filter cartridge even before
using it for 100 hours.
CC
CC
ll
ll
ee
ee
aa
aa
nn
nn
ii
ii
nn
nn
gg
gg
oo
oo
rr
rr
rr
rr
ee
ee
pp
pp
ll
ll
aa
aa
cc
cc
ee
ee
mm
mm
ee
ee
nn
nn
tt
tt
oo
oo
ff
ff
tt
tt
hh
hh
ee
ee
rr
rr
ee
ee
aa
aa
rr
rr
ff
ff
ii
ii
ll
ll
tt
tt
ee
ee
rr
rr
ii
ii
nn
nn
gg
gg
ss
ss
pp
pp
oo
oo
nn
nn
gg
gg
ee
ee
Unhook the lever for opening the air output filter screen (17) and turn it upwards. After
removing the HEPA filter take out the filter sponge and clean it. Do this periodically, washing
it in running water. If it has deteriorated replace it with a Polti original spare part.
Fig. 15
TT
TT
RR
RR
OO
OO
UU
UU
BB
BB
LL
LL
EE
EE
SS
SS
HH
HH
OO
OO
OO
OO
TT
TT
II
II
NN
NN
GG
GG
The suction fan will not start
The suction fan switches off
during suction and the four
indicator lamps start flashing.
The boiler filling pump can be
heard working continuously
The suction power drops.
The appliance does not respond
to commands.
Water is spilled while sucking
up liquids.
No power supply
The level of the liquid inside the
tank is too high.
The output power selected is
too high for the type of surface.
Air in the boiler circuit.
The upholstery nozzle, the
flexible suction tube or the stiff
suction tube are clogged.
HEPA filter exhausted.
The HEPA filter may be wet
The circuit board has received
electronic signals from an
unrelated appliance
Float device clogged.
Check the cable, plug and socket.
Press the switch (1), disconnect the
power cable from the mains plug
and lower the level of the water in
the tank to the level indicated.
Press the switch (1), disconnect
the power cable from the mains
plug and leave the appliance
disconnected for at least 30" in
order to enable the safety
device to reset.
Switch off the appliance, allow it
to cool and repeat the
operations described in the
"Operation" chapter.
Clean the filter and remove any
obstruction from the tubes and
accessories
Replace the filter.
Remove the HEPA filter and
leave it to dry
Disconnect the appliance from
the mains for few minutes and
then try again
Clean the "EcoActive Filter"
water-based filter assembly.
Problem Cause What to do
