645078
7
Zoom out
Zoom in
Vorherige Seite
1/10
Nächste Seite
POWX0650 EN
Copyright © 2016 VARO P a g e | 7 www.varo.com
7.4 Adjusting the case width (Fig. 4, Fig. 5, Fig. 6, Fig. 7)
The machine is supplied with four spacer rings (15) which are each approximately 10 mm
thick. The chase width can be adjusted by varying the amount of spacer rings fitted
between the diamond cutting discs. The chase width can be calculated by taking into
account the thickness of the spacer rings and the width of the diamond cutting discs. The
maximum chase width is approximately 44mm.
7.5 Dust extraction
The machine may only be operated when connected to a suitable vacuum device, the
vacuum device must be approved for stone dust. A dust extraction adapter (3) is supplied,
ensure that the hose is securely attached to the adapter. Stop work immediately when the
vacuum device breaks down. Switch the machine off and restore the vacuum device. The
vacuum device must be suitable for the type of material you work with. Use a special
vacuum device when working with toxic materials or where toxic dust is produced. Use of
a household vacuum cleaner may damage your health.
For best results use a wet and dry vacuum device fitted with an appropriate filter. If in
doubt seek expert advice.
8 OPERATION
Mark the line of cut before starting work, hold the machine tightly with both
hands. (Fig. 8)
1. Set the chase depth. Place the front roller wheel of this machine firmly against the wall.
Switch the machine on and gently lower the machine towards the wall until the rotating
diamond cutting discs plunge into the wall, hold the machine tightly with both hands.
2. Carry out the cut steadily, evenly and with moderate pressure appropriate to the material
being cut. Ensure you work in the correct direction! Always work against the direction of
rotation as shown on the machines protective guard to avoid the risk of the machine
being forced uncontrolled of the cut.
3. After completing the cut, retract the machine slightly, switch off and remove from the cut.
Allow the diamond cutting discs to stop before putting the machine down. Do not attempt
to brake the diamond cutting discs by applying lateral pressure.
Remove the remaining masonry in the chase using the masonry breaking tool provided.
It is not possible to make curved cuts with the machine as the diamond cutting discs may
seize in the cut.
Paving slabs or similar must be placed on a solid surface or be otherwise securely
supported before starting the cut to avoid breakage.
When cutting especially hard material, e.g. concrete with high gravel content, the diamond
cutting discs can overheat and become damaged. This is indicated by a ring of sparks that
rotates with the diamond discs. In this case, interrupt the cutting process and allow the
diamond discs to cool down by running the machine at no-load for a short time.
Noticeably decreasing work progress and a rotating spark ring indicate that the diamond
cutting discs have become blunt.
9 CLEANING AND MAINTENANCE
WARNING: Disconnect the unit from the mains before carrying out any
maintenance or adjustments.
7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Powerplus POWX0650 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Powerplus POWX0650

Powerplus POWX0650 Bedienungsanleitung - Deutsch - 12 seiten

Powerplus POWX0650 Bedienungsanleitung - Holländisch - 11 seiten

Powerplus POWX0650 Bedienungsanleitung - Französisch - 11 seiten

Powerplus POWX0650 Zusatzinformation - Alle Sprachen - 3 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info