Bedienungsanleitung Powerplus POWXG9008 (Seite 8 von 13) (Englisch)

582181

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

POWXG9008 EN

11 OPERATING INSTRUCTIONS

11.1 Pressure washer location

 Locate the pressure washer on a solid and level surface so that the engine and pump

crankcase oil lubricate components properly. Avoid areas where puddles are pounded.

Slippery surfaces can cause injuries..

 Locate the machine in a well-ventilated area and away from flammable materials or fumes.

Be sure ventilation warnings are observed. Keep pressure washer at least 18”away from

flammable materials.

 Locate the machine in a way, that the operator has easy access to the pressure washer

and its controls. Locate the machine so that it is protected from external damage.

 To prevent damage and excessive hose wear; locate the pressure washer so that the

hose does not cross traffic areas.

11.2 Start-up procedure (Fig. 11 &12)

 Place pressure washer on a level surface.

 Turn on the water

 Purge the system’s pump of air by releasing the safety and squeezing the trigger of the

spray gun.

 Attach the lance to the spray gun.

 Turn fuel valve to the ‘ON’ position.

 Slide the choke lever to the ‘CHOKE’ position

 Turn the engine OFF/ON switch to the ‘ON’ position.

 Holding the machine with your hand, pull the recoil handle (starter cord) slowly until

resistance is felt, then pull rapidly. Squeeze the trigger gun and release the pressure after

every failed attempt to start the pressure washer (this will reduce the back pressure)

 Let engine run for several seconds and then gradually slide the choke lever to the RUN

position as the engine warms up until the choke is fully slid to the RUN position.

11.3 Stopping pressure washer (Fig. 13)

 Turn the on/off switch to the OFF position.

 Turn the fuel valve to the OFF position.

 Turn off the water and squeeze the trigger handle to release all water pressure.

11.4 Adjusting the spray pattern (Fig. 14)

Warning: Always ensure that the wand is fixed correctly. Otherwise it could be injected under

high pressure when operating the gun, possibly causing injury or damage.

11.4.1 0° nozzle (colored red)

This nozzle delivers a pinpoint stream and is extremely powerful. It covers a very small area of

cleaning. This nozzle should only be used on surface that can withstand this high pressure

such as metal or concrete. Do not use on wood.

11.4.2 15° nozzle (colored yellow)

This nozzle delivers a powerful 15 degree spray pattern for intense cleaning of small areas.

This nozzle should only be used on areas that can withstand the high pressure from this

nozzle.

11.4.3 40° nozzle (colored white)

This nozzle delivers a 40 degree spray pattern and a less powerful stream of water. It covers a

wide area of cleaning. this nozzle should be used for most general cleaning jobs.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWXG9008 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWXG9008

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info