Bedienungsanleitung Profile PIN-136 (Seite 1 von 2) (Englisch)

566798

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

3-in-1 DIGITAL DETECTOR EN - 1

PIN-136

We thank you for the purchase of this Profile product.

Please note: It is important that you read this manual

before using the product And be sure to save this

manual for possible use later.

Features and advantages

1. foot for vertical fixing

2. Spirit level

3. Feet for horizontal fixing

4. foot for spirit level

5. Function key metal

6. Function key laser

7. Function key wood

8. on-key

9. LCD display

10. Adjusting ring laser angle

Features and advantages

 Detection of wood/metal and live 230V wires –

detects to a depth of maximum 3/4" (19 mm)

 Signals obstacles with a noise and displays this on the

LCD display. 180” adjustable laser with spirit level

and perpendicular line glass

 LCD display with graphic display

 LED light for continuous detection of live wires

 Laser line projection 6.5 metres

 With adjustable legs for bringing the laser level

 Vertical and horizontal fixing feet

 Simple key operation

 Ergonomic designed to enhance comfort and grip

 Automatic switching off

 Low battery capacity indication

Safety instructions

If the warnings are not heeded this can result in

physical injury.

Heed the following warnings to prevent physical

injury:

• Never remove the warning labels.

• Do not point the laser beam directly at other people's

eyes.

• NEVER look directly into the laser beam.

• Do NOT point the laser beam at a reflective surface.

• Do NOT use near children and do not allow use by

children.

• Never disassemble the laser.

Always switch the laser off when the appliance is not

in use.

Introduction

The unit uses electronic signals to locate the position of

wooden beams, connections or live AC wires under

plasterwork and

other common wall materials. When the edge of the

beam/plank is detected the unit's LCD display gives a

visual and acoustic signal to enable you to

exactly determine the edge of the beam. You can mark

the place of the beam edges with a pencil line. The unit

generates a vertical laser plane and turns 45 or 90

degrees to the right or to the left to generate a straight

laser line.

Operating instructions

Detection mode is selected with the function keys - metal

or wood.

The standard mode is the detection of wooden beams.

The preferred mode must be selected before "on" is

pressed.

Calibration

Calibrate the unit on a wall before you scan for wooden

or metal elements or power lines.

Please note! The calibration of the unit must take place

on a wall in which you know there are no wooden/metal

or electrical parts. Still wet or just painted surfaces can

also affect the good calibration of the unit. If you

do not adhere to the points mentioned above, the unit

will not give the correct location of concealed objects in

walls and ceilings.

Different surfaces

Wallpaper: there is no difference in the operation of the

sensor with surfaces hung with wallpaper or textiles

unless this wallpaper contains metallic foil or fibres.

Plasterwork or lath walls: the unit will function

correctly unless the plasterwork or laths are

exceptionally thick or contain metal meshing.

Ceilings or surfaces with a textured finish: when a

rough surface has to be scanned, such as a sprayed

textured ceiling, you can use a piece of cardboard to

scan the surface. Carry out the abovementioned

calibration WITH the piece of cardboard between the

sensor and the surface.

Detection of wooden beams

When the unit is switched on, as default it is in the

detection mode for wooden beams.

1. Slide the unit in a straight line over the surface. As

the unit comes closer to the beam, more lines will

be seen as shown in picture 2. When the edge of

the beam is detected, the wood indication and the

edge line will be seen as in figure 3. The unit

sounds a repeated beeping.

2. Use the indication line to mark the edge of the

beam.

3. Slide further over the beam. When the indication

goes out and the unit stops beeping the other edge

has been detected.

4. Carry out an extra check of the location of the beam

by approaching it from the other side.

5. The middle point between the markings indicates

the middle of the beam.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Profile PIN-136 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Profile PIN-136

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info