Bedienungsanleitung Reer 50133 Care and talk (Seite 18 von 57) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

716181

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

34 35

Child unit (star motif)

Hold down button while turning on device. (Hold down both outer buttons in parallel).

Press / buttons and select bA. The child symbol will be displayed. In order to save

the settings, brieﬂy press the PTT button.

Parental unit (without motif)

Hold down button while turning on device. (Hold down both outer buttons in parallel).

Press / buttons and select PA. The parental symbol will be displayed. In order to

save the settings, brieﬂy press the PTT button.

Now the channel (01 to 18) is displayed, which, on the child unit, is supplemented by the

letter b, or on the parent unit, by the letter P. Then, the corrsponding symbols or

will be displayed.

Using several child units

With the help of several child units, you can monitor multiple children, event. multiple

rooms. For this, all devices must be set to the same channel. When using in this way, we

recommend deactivating reach control, as due to variouse devices, false alarms may occur.

Keep in mind that in the parental unit, you can hear only one child at a given time. Besides

this, you should lower the volume on child units to 0, as otherwise, the children could mu-

tually listen to each other or disturb each other.

Chapter 2: Use in „walkie talkie“ operating moden

Both devices are factory-set to the „baby monitor operating mode. If you wish to re-set the

devices to the operating mode „radio device PMR446“, execute the following steps.

Hold down the button while turning on the device (hold down the OFF/ON button for

several seconds). By pressing the / button, select ro. In order to save the settings,

brieﬂy press the PTT button.

Selection of PMR446 channel

This broadcasting/receiving system has 8 PMR446 channels available. On top of this, you

can select individual PMR446 coding for each channel individually through CTCSS tones (38

possible codes). The code will appear to the right of the number of the channel as a small

two-digit number between 01 and 38 or oF.

Make sure that all devices are set to the same channel and CTCSS tone.

Press button 1× and then choose the required PMR446 channel with the help of /

buttons.

Setting CTCSS or DCS code

Additional CTCSS or DCS codes serve to prevent listening in on other conversations on the

same channel. This does not mean, however, that the transmission is protected against in-

terception. There is always the possibility that unencrypted analog radio signals will be inter-

cepted. CTCSS (Continuous Tone Coded Squelch Signal) or DCS (Digital Coded Squelch) tones

are tones beyond the low frequency audibility threshold, which are transmitted together

with the microphone signal. In case of reception, the device will check whether a CTCSS or

DCS tone is transmitted and will turn on the speaker only when the correct code is received.

Setting the CTCSS code:

Press button once. 01–38 or oF ﬂashes on the display. For setting the required code, press

/ buttons. In order to save the settings, brieﬂy press the PTT button.

Setting the DCS code:

Press the button 2×. 01–38 or oF ﬂashes on the display. For setting the required code,

press / buttons. In order to save the settings, brieﬂy press the PTT button.

Warning: it is possible to activate only CTCSS or DCS.

Transmission

To broadcast, press and hold down PTT button. To receive, let go the button again.

Searching for channels

This function will search all PMR446 channels according to signal. To start search, hold down

button for a long time. The search is interrupted as soon as the signal is captured. You

can then listen to the channel for a period of 8 seconds, until the search continues. After

ending the search, hold down button for a long time once again.

Warning: searching channels is availavle only in the „PMR446“ operating mode.

Ringtone selection

Press button 9×.C will appear on the display, as well as current settings, which will ﬂash.

To select ringtone from possibilities 01-03 or oF, press / buttons. In order to save the

settings, brieﬂy press the PTT button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Reer 50133 Care and talk Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info