587711
23
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
Functional test for
cooling mode.
1. Switch the supply voltage on.
2. Use the remote control to turn
on the unit and select the cool-
ing mode, maximum fan speed
and lowest nominal tempera-
ture.
Commissioning
Commissioning should only be
performed by specially trained
personnel and documented
after the certificate has been
issued.
Observe the manuals for the
indoor unit and outdoor unit
when commissioning the en-
tire system.
NOTE
Check the DIP switch settings
on the PCB, as illustrated on
Page 22.
If necessary, set the DIP
switches to the appropriate
indoor unit type.
NOTE
Functional test for
heating mode.
1. Switch the supply voltage on.
2. Use the remote control to
switch on the unit and select
the heating mode, maximum
fan speed and highest nominal
temperature.
Final tasks
Reassemble all disassembled
parts.
Familiarise the operator with
the system.
3. Measure and record all the
required values in the commis-
sioning report and check the
safety functions.
4. Check the control system for
the unit using the functions
described in the chapter "Opera-
tion". Timer, temperature setting,
fan speeds and changing to air
circulation or dehumidifying
mode.
5. Check the correct function of the
condensation line by pouring
distilled water into the conden-
sation tray.
A bottle with a spout is recom-
mended for pouring the water
into the condensation tray.
3. Measure and record all the
required values in the commis-
sioning report and check the
safety functions.
4. Measure the air intake tem-
perature of the ceiling mounted
cassette and the room tempera-
ture approx. 1.5 m above the
floor. In the event of deviation,
correct any temperature dif-
ference by means of the DIP
switch SW1 (s.S22).
5. Check the control system for
the unit using the functions
described in the chapter "Op-
eration".
Timer, temperature setting, fan
speeds.
Check that the stop valves
and valve caps are tight after
carrying out any work on the
refrigerant circuit. Use ap-
propriate sealant products as
necessary.
NOTE
23
650
650
400
620
28
580
MXD 200-520 IT
Unit dimensions
255
580
23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für REMKO MXD350 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von REMKO MXD350

REMKO MXD350 Bedienungsanleitung - Deutsch - 24 seiten

REMKO MXD350 Bedienungsanleitung - Holländisch - 24 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info