167805
26
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
26
4. ELECTRICAL wIRING
4.2 LOUDSPEAKER CABLES
Connect the loudspeaker wires to the speaker terminals of the
amplifier. Use good quality wires of 2.5mm² cross-section.
When baring wires, remove approximately 6-8mm of the insu-
lation and after axially twisting the wires; insert the bare ends
into the corresponding speaker terminal output on the amplifier.
Be sure to follow correct polarity ("+" to "+"; "-" to "-"). Tighten
the terminal screws on the amplifier.
4.3 CONNECTION OF POWER CABLES
Run the positive power cable ("+12 V") directly from the positive
terminal of the car battery to the amplifier. Make sure the power
cable makes good contact to the battery; i.e. use an approp-
riate battery clamp that accepts big gauge power cables! For
protection of your car audio system and your entire car against
electrical fire hazards from a short-circuit of the main power
cable with chassis ground, you must insert a main fuse (holder)
within the first 30cm of the battery. The fuse type/value should
be matching the limitations of your main power cable and the
requirements of your car audio system. For example 80 A fuse
when using the 35 mm² power cable.
Now you route the ground cable to the amplifier. It is best to
keep the ground cable ("-12V") as short as possible, i.e. to find
a chassis contact very close to the amplifier. The ground power
cable must have the same cross-section as the positive power
cable. It is recommended to use a corrosion-resistant gold-pla-
ted power ring or a massive ground clamp between the ground
cable and the chassis ground point. Keep in mind that audible
interferences and problems originating in the power supply of
the amplifier, are mostly based on a bad ground contact.
4. ELECTRICAL WIRING
IMPORTANT! Disconnect the positive battery ter-
minal (+12V) or remove the main fuse near the car
battery before you start any wiring work!
The power supply of the car audio system must be
disconnected until the entire wiring installation is
completed.
Use rubber grommets when running cables through any me-
tal or sharp plastic panels, to prevent accidental shorting or
shearing. Make sure the cables do not interfere with normal
operation of the vehicle.
Especially the music signal cables (RCA interconnects) should
be kept far away from any potential sources of electrical inter-
ference i.e. electronic vehicle management systems (engine
computers, relays etc.) fuel pumps, wiring harnesses etc.!
4.1 RCA INTERCONNECTS / REMOTE
LEAD
Carefully run the RCA audio signal interconnect(s) and the
remote switching cable from the head-unit to the amplifier.
The audio signal cables should be routed completely separate
from the power cables. Use only double or triple shielded quality
cables!
Connect the remote wire lead to the remote output of the head-
unit and to the remote input terminal of the amplifier. Finally
connect the RCA interconnect cable(s) to the respective outputs
on the head-unit and the RCA inputs of the amplifier.
Ro 1-2-4-CH Manual_D+E def.indd 26 01.03.2006 10:55:37 Uhr
26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Rodek r 1900 n wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info