Bedienungsanleitung Roland BK-9 - Midi Implementation (Seite 3 von 26) (Englisch)

708968

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

MIDI Implementation

• Some Tones will not exhibit any change.

• Not received when MIDI “Rx” part parameters is “O”.

• Not received when the “Other CC” parameter of the MIDI “Rx

Event” group is “O”

{ Vibrato Delay (Controller Number 78)

Status 2nd byte 3rd byte

BnH 4EH vvH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

vv = Vibrato Delay value (relative change): 00H-7FH(-64 - 0 -+63),

Initial value=40H (no change)

• Some SuperNatural Tones will not exhibit any change.

• Not received when MIDI “Rx” part parameters is “O”.

• Not received when the “Other CC” parameter of the MIDI “Rx

Event” group is “O”

{ Staccato (SuperNATURAL, Controller Number 80)

Status 2nd byte 3rd byte

BnH 50H vvH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

vv = Vibrato Delay value (relative change): 00H-7FH(-64 - 0 - +63),

Initial value=40H (no change)

• Some SuperNatural Tones will not exhibit any change.

• Not received when MIDI “Rx” part parameters is “O”.

• Not received when the “Other CC” parameter of the MIDI “Rx

Event” group is “O”

{ Fall (SuperNATURAL, Controller Number 81)

Status 2nd byte 3rd byte

BnH 51H vvH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

vv = Vibrato Delay value (relative change): 00H-7FH(-64 - 0 - +63),

Initial value=40H (no change)

• Some SuperNatural Tones will not exhibit any change.

• Not received when MIDI “Rx” part parameters is “O”.

• Not received when the “Other CC” parameter of the MIDI “Rx

Event” group is “O”

{ Portamento Control (Controller Number 84)

Status 2nd byte 3rd byte

BnH 54H kkH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

kk = source note number: 00H-7FH (0-127)

• A Note-on received immediately after a Portamento Control

message will change continuously in pitch, starting from the pitch

of the Source Note Number.

• If a voice is already sounding for a note number identical to the

Source Note Number, this voice will continue sounding (i.e.,

legato) and will, when the next Note-on is received, smoothly

change to the pitch of that Note-on.

• The rate of the pitch change caused by Portamento Control is

determined by the Portamento Time value.

• Not received when MIDI “Rx” part parameters is “O”.

• Not received when the “Other CC” parameter of the MIDI “Rx

Event” group is “O”

Example 1.

On MIDI Description Result

90 3C 40 Note on C4 C4 on

B0 54 3C Portamento no change (C4 voice still

sounding)

Control from C4

90 40 40 Note on E4 glide from C4 to E4

80 3C 40 Note o C4 no change

80 40 40 Note o E4 E4 o

Example 2.

On MIDI Description Result

B0 54 3C Portamento no change

Control from C4

90 40 40 Note on E4 E4 is played with glide from

C4 to E4

80 40 40 Note o E4 E4 o

{ Eect 1 (Reverb Send Level) (Controller Number 91)

Status 2nd bytes 3rd byte

BnH 5BH vvH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

vv = Control value : 00H-7FH (0-127)

•

• This message adjusts the Reverb Send Level of each Part.

• Not received when “Reverb” RX Event is O.

• Not received when MIDI “Rx” part parameters is “O”.

{ Eect 3 (Chorus Send Level) (Controller Number 93)

Status 2nd byte 3rd byte

BnH 5DH vvH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

vv = Control value: 00H-7FH (0-127)

Initial Value = 00H (0)

• This message adjusts the Chorus Send Level of each Part.

• Not received when “Chorus” RX Event is O.

• Not received when MIDI “Rx” part parameters is “O”.

{ NRPN MSB/LSB (Controller Number 99, 98)

Status 2nd byte 3rd byte

BnH 63H mmH

BnH 62H llH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

mm = upper byte (MSB) of the parameter number specied by NRPN

ll = lower byte (LSB) of the parameter number specied by NRPN

• The value set by NRPN will not be reset even if Program Change or Reset All

Controllers is received.

• Not received when “NRPN” RX Event is O.

• Not received when MIDI “Rx” part parameters is “O”.

**NRPN**

The NRPN (Non Registered Parameter Number) message allows an extended

range of control changes to be used. On the BK-9, NRPN messages can be used to

modify sound parameters, etc.

To use these messages, you must rst use NRPN MSB and NRPN LSB messages

to specify the parameter to be controlled, and then use Data Entry messages to

specify the value of the specied parameter. Once an NRPN parameter has been

specied, all Data Entry messages received on that channel will modify the value

of that parameter. To prevent accidents, it is recommended that you set RPN

Null (RPN Number = 7FH/7FH) when you have nished setting the value of the

desired parameter. On the BK-9, Data entry LSB (Controller number 38) of NRPN

is ignored, so it is no problem to send Data entry MSB (Controller number 6) only

(without Data entry LSB).

On this instrument, NRPN can be used to modify the following parameters.

NRPN Data entry

MSB LSB MSB Description

01H 08H mmH Vibrato Rate (relative change) mm: 0EH-40H-72H

(-50 - 0 - +50)

01H 09H mmH Vibrato Depth (relative change) mm: 0EH-40H-72H

(-50 - 0 - +50)

01H 0AH mmH Vibrato Delay (relative change) mm: 0EH-40H-72H

(-50 - 0 - +50)

01H 20H mmH TVF Cuto Frequency (relative change)

mm: 0EH-40H-72H (-50 - 0 - +50)

01H 21H mmH TVF Resonance (relative change)

mm: 0EH-40H-72H (-50 - 0 - +50)

01H 63H mmH TVF &TVA Envelope AttackTime (relative change) mm:

0EH-40H-72H (-50 - 0 - +50)

01H 64H mmH TVF &TVA Envelope DecayTime (relative change) mm:

0EH-40H-72H (-50 - 0 - +50)

01H 66H mmH TVF &TVA Envelope ReleaseTime (relative change) mm:

0EH-40H-72H (-50 - 0 - +50)

Roland BK-9 - Midi Implementation Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info