Bedienungsanleitung Rommelsbacher EBW3208IN (Seite 16 von 20) (Deutsch, Englisch)

714021

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Switching off with the ON/OFF sensor (1) when the key lock is active

When the key lock is active and the control is switched off by means of the ON/OFF sensor (1), the LED

above the key lock (2) extinguishes. When switching on again, the key lock (2) is active again until it is

deactivated as described above!

5.2 Pot recognition

If there is no or no suitable wok pot on the switched-on cooking zone, there will be no power

transfer. The blinking “ ” indicates that.

If a qualified pot is placed in the cooking zone, the set level will switch on and the cooking level

indication will glow. The energy supply will be cut if the vessel is removed. A blinking “ ”

appears in the cooking level display and the cooking zone is switched off automatically.

Self-help:

Make sure that the used cookware is qualified for induction cooking. Test the magnetizability of

the pot or ask the pot manufacturer.

Note: Small metal objects like forks or spoons as well as pots made of unsuitable material are not

recognised.

5.3. Safety shut-down during permanent activation

If one or more sensors are applied for more than 10 seconds (e. g. by objects or overrun food

on the operation panel) there will be an audible alarm message for 5 seconds and the lightning

symbol shown on the left will appear in the display. Remove the cause in this case and then put

the appliance into operation again.

If the ON/OFF sensor is permanently activated, the appliance will switch off and cannot be

switched on again without remedying the problem!

Self-help: Remove the cause of the permanent activation. After cleaning the sensor panel, the cooking

zone can be put into operation again.

5.4. Multiple activation

If more sensors are applied simultaneously, no function will be carried out.

5.5. Temperature control of the cooking zone

The cooking zone is equipped with a temperature sensor below the glass ceramic plate. The control is

effected in three steps.

If the first (lower) temperature limit at the cooking zone is passed, a possibly active booster function will be

deactivated automatically. The indication “P” blinks for 3 seconds firstly, afterwards the control sets the

cooking level “9”.

If the second (middle) temperature limit at the cooking zone is passed, the control will automatically reduce

the power supply to avoid a further temperature increase. However, the display continuous showing the set

cooking level!

If the third (upper) temperature level is passed, the cooking zone will be automatically switched off. The

error code “E2” (excess temperature) appears in the display.

5.6. Operating time limitation

The operating time limitation causes an automatic switch-off of the cooking zone if there has not been any

change of the settings for a certain period. The operating time limitation is depending on the set level (see

chart). After an automatic switch-off, the cooking zone can be switched on again and the maximum

operating time is active again.

However, timer settings have priority to the operating time limitation i. e. the cooking zone is only switched

off after the timer has elapsed and not when the operating time limitation requires that!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rommelsbacher EBW3208IN Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info