Bedienungsanleitung Rotel rcd 1072 (Seite 6 von 10) (Englisch)

161721

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

RCD-1072 Stereo Compact Disc Player

AC Power and Control

AC Power Input

Your RCD-1072 is configured at the factory

for the proper AC voltage in the country where

you purchased it (either 115 volts or 230/ 240

volts. The AC line configuration is noted on a

decal on the back panel.

Note: Should you move your CD player to

another country, it may be possible to

reconfigure it for use on a different line

voltage. Do not attempt to perform this con-

version yourself. Opening the enclosure of

the RCD-1072 exposes you to dangerous

voltages. Consult a qualified service person

or the Rotel factory service department for

information.

The RCD-1072 should be plugged directly into

a 2-pin polarized wall outlet or into the

switched outlet on another component in your

audio system. Do not use an extension cord.

Be sure the power switch on the front panel

of the RCD-1072 is turned off (in the “out”

position). Then, connect the supplied power

cord to the AC power receptacle on the rear

of the unit and the AC power outlet.

If you are going to be away from home for

an extended period of time such as a month-

long vacation, it is a sensible precaution to

unplug your CD player (as well as other au-

dio and video components) while you are

away.

Power Switch and Power

Indicator

The power switch is located on the front panel

of your CD player. To turn the CD player on,

push the switch in. The LED indicator above

the switch and the Display will light up, indi-

cating that the CD player is turned on. To turn

the CD player off, push the button again and

return it to the “out” position.

Note: If you are using a switched outlet to

turn on and off your CD player, you should

leave the power switch in the “on” position.

When AC power is applied to the unit, it

will power up in fully active mode.

Output Connections

The RCD-1072 gives you a choice of two dif-

ferent kinds of outputs – an analog output signal

from the built-in D/A converter for use with

conventional analog audio components and

a coax digital output which provides an un-

processed digital signal for use with outboard

D/A converters or digital processors.

Note: To prevent loud noises that could

damage your speakers, turn off all the sys-

tem components when you make any signal

connections.

Analog Outputs

[See Figure 3 for wiring illustration]

A pair of standard RCA jacks supplies an

analog output signal from the RCD-1072 to

the source inputs of an audio preamplifier, in-

tegrated amplifier, or receiver.

Select high quality audio interconnect cables.

Connect the left and right channel outputs of

the RCD-1072 to the corresponding inputs on

the preamplifier or other component.

Digital Output

[See Figure 4 for wiring illustration]

If you are using an outboard D/A converter

or other digital processor, you will need an

unprocessed digital data stream from the

RCD-1072. Using a standard 75 ohm coax

digital cable, connect the RCD-1072’s digi-

tal output to the digital input connector on the

outboard D/A converter.

12 Volt Trigger Input

The RCD-1072 can be activated by a 12 volt

trigger signal. The trigger input accepts any

control signal (AC or DC) ranging from 3 volts

to 30 volts. When a cable is connected to the

12V input and a trigger signal is present, the

RCD-1072 is activated. When the trigger signal

is turned off, the unit goes into standby mode.

The front panel power indicator remains lit,

but the display goes dark and the unit will not

operate.

NOTE: When using the 12V Trigger fea-

ture, leave the POWER button in the ON

position.

EXT REMOTE IN Jack

This 3.5mm mini-jack receives command codes

from industry-standard infrared receivers

(Xantech, etc.) via hard-wired connections. This

feature could prove useful when the unit is

installed in a cabinet and the front-panel sensor

is blocked. Consult your authorized Rotel dealer

for information on these external repeaters and

the proper wiring of a jack to fit the mini-jack

receptacle.

Operation

The RCD-1072 can be operated using its front

panel buttons or from corresponding buttons

on the supplied infrared remote control. Spe-

cific instructions for each of these controls are

detailed below. Most of the buttons are du-

plicated on the front panel and on the IR re-

mote control. However, there are a few ex-

ceptions where the buttons are only available

on one or the other. These exceptions are noted

in the instructions.

Infrared Remote Control

Before using the IR remote control, it is nec-

essary to install two “UM-4/AAA” batteries

(supplied). Remove the plastic cover on the back

of the IR remote, install the batteries (observ-

ing the + and – polarity indications), and

reinstall the cover.

To use the IR remote control, aim it at the IR

sensor

located in the lower left corner of

the RCD-1072 front panel.

Display

A lighted Display on the front panel of the

RCD-1072 provides useful information about

the status of the unit, activation of special fea-

tures, and track/time information for the disc

being played. Each of these indicators is de-

scribed in the detailed operating instructions

that follow.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Rotel rcd 1072 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info