629984
16
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
XML POWERED MIXERS
16
Speaker Outputs - XML410
The XML410 contains two mono power ampliers, and depending on the operating mode, the two ampliers can be
used independently (maximum output 200W + 200W) or in BRIDGE mode (maximum output 400W).
NOTE: Use the front panel Power Amp MODE switch to select which signal is sent to the speaker output jacks, and to
activate BRIDGE mode.
If the two power ampliers are used for MAINS operation, two 8 Ohm speakers can be daisy-chained” together and con-
nected to the AMP 1 jack, and two more 8 Ohm speakers can be daisy-chained” together and connected to the AMP 2
jack, for a total of four speakers.
The total impedance load for each amplier must not exceed 4 Ohms. Therefore, in the example above, two speakers with
an impedance of 8 Ohms each are connected to each amps output jacks.
If you wish to use two ampliers independently, lets say for Main and Monitor operation, use a 4–8 Ohm speaker. Again,
the total impedance load for each amplier must not exceed 4 Ohms. Therefore, two speakers with an impedance of 8
Ohms can be daisy-chained” together and then connected to each amps output jacks.
If two ampliers are used in a BRIDGE mode, only one speaker can be connected to the BRIDGE jack. The total impedance
load while operating in BRIDGE mode must not be less than 8 Ohms. If you are connecting a speaker to the BRIDGE jack,
use an 8–16 Ohm speaker.
CAUTION: When using a BRIDGE connection, do not connect anything to the AMP 1 and AMP 2 jacks. Likewise, when us-
ing the AMP 1 and AMP 2 jacks, do not connect anything to the BRIDGE jack.
44. AMP 1 Speaker Outputs - The AMP 1 output has one 1/4” phone connector, which is a powered output used to con-
nect your main PA speaker when using the XML410 in MAIN/MAIN mode. When operating in MAIN/MONITOR mode,
the AMP 1 powered output connectors are used to connect left and right side MAIN PA speakers.
45. AMP 2 Speaker Outputs - The AMP 2 output has one 1/4” phone connector, which is a powered output used to con-
nect your main PA speaker when using the XML410 in MAIN/MAIN mode. When operating in MAIN/MONITOR mode,
the AMP 2 powered output connectors are used to connect to oor or side ll monitors facing the performers.
46. BRIDGE Output connector - The BRIDGE output has one 1/4” phone connector, which is a powered output used to
connect one main PA speaker when using the XM410 in BRIDGE mode.
44 4546
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Samson XML910 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Samson XML910

Samson XML910 Bedienungsanleitung - Deutsch - 32 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info