Bedienungsanleitung Scheppach DP19Vario (Seite 29 von 148) (Deutsch, Englisch, Französisch, Italienisch, Polnisch)

781654

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 29

Such damaged electrical connection cables must not be

used and are life-threatening due to the insulation dam-

age.

Check the electrical connection cables for damage reg-

ularly. Ensure that the connection cables are discon-

nected from electrical power when checking for dam-

age.

Electrical connection cables must comply with the ap-

plicable VDE and DIN provisions. Only use connection

cables with the marking „H05VV-F“.

The printing of the type designation on the connec-

tion cable is mandatory.

AC motor

• The mains voltage must be 230 V~

• Extension cables up to 25 m long must have a

cross-section of 1.5 mm2.

Connections and repairs of electrical equipment may

only be carried out by an electrician.

Please provide the following information in the event

of any enquiries:

• Type of current for the motor

• Machine data - type plate

11. Cleaning and maintenance

Pull the mains plug before any adjustments,

maintenance or repair.

m Have any work on the device that is not de-

scribed in this instruction guide performed by a

professional. Only use original parts. Allow the

device to cool off before any maintenance or

cleaning is undertaken. There is a risk of burn-

ing!

Always check the device before using it for obvi-

ous defects such as loose, worn or damaged parts,

correct the positioning of screws or other parts. Ex-

change the damaged parts.

Cleaning

Do not use any cleaning agents or solvents. Chemi-

cal substances could damage the plastic parts of the

device. Never clean the device under running water.

• Clean the device thoroughly after each use.

• Clean the ventilation holes and the surface of the

device with a soft brush or cloth.

• Remove the swarf, dust and dirt with a vacuum

cleaner if necessary.

• Lubricate the moving parts regularly.

• Do not allow lubricants to come into contact with

switches, V-belts, pulleys and drill lifting arms.

6 1270 800 1100 4800 4000

7 1090 680 960 4100 3400

8 960 600 840 3600 3000

9 850 530 740 3200 2650

10 765 480 670 2860 2400

11 700 435 610 2600 2170

12 640 400 560 2400 2000

13 590 370 515 2200 1840

14 545 340 480 2000 1700

16 480 300 420 1800 1500

18 425 265 370 1600 1300

20 380 240 335 1400 1200

22 350 220 305 1300 1100

25 305 190 270 1150 950

Countersinking and center-drilling

With this table drill, you can also countersink and

center-drill. Please observe that countersinking

should be performed at the lowest speed, while a

high speed is required for center-drilling.

Drilling wood

Please note that sawdust must be properly evacuated

when working with wood, as it can pose a health haz-

ard. Ensure that you wear a suitable dust mask when

performing work that generates dust.

10. Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies

with the applicable VDE and DIN provisions. The

customer‘s mains connection as well as the ex-

tension cable used must also comply with these

regulations.

Important information

In the event of overloading, the motor will switch itself

off. After a cool-down period (time varies) the motor

can be switched back on again.

Damaged electrical connection cable

The insulation on electrical connection cables is of-

ten damaged.

This may have the following causes:

• Pressure points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been improp-

erly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach DP19Vario Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info