- 10 - Copyright © 2020, F 07/2020
Cancelling scheduled cleaning
Hold down the button E3 (PLAN).
on the display E2 .
Hold down button E9 (ON/OFF) until 00:00 appears on the display
E9 again will cancel the set time and the vacuum cleaner will beep 2x.
Hold down button E3 (PLAN) to return to the display of the system time
CHARGING
AUT
As soon as the vacuum cleaner detects low voltage of the battery during operation,
it will automatically start to seek out the charging station. In order for it to find it and
dock, it needs to find the infrared signal transmitted by the charging sta
reason, we recommend leaving the char
power source and located in ac
LOCA
After docking in the charging station, the charging cycle will commence. A
charge takes approximately 4 t
power level of the battery fully charged battery will provide up to 90 minutes
of operation.
During the charging process, the indicator light on buttA2 will flash red.
When the battery is fully charged, the indicator light of button A2 will remain
permanently lit blue and the process will end automatically
In the event that the charging contacts are disconnected during the charging cycle,
the vacuum cleaner will move away fr
itself to resume the charging process
obstacle. In the event of apower outage, the char
will continue after the power supply is renewed
charging current is exc
charging cycle.
MANUAL CHARGING
If the vacuum cleaner is located away from the charging sta
battery voltage then button A2 will start flashing red 2x per second. Press button E4
(HOME) on the remote control.
charging station and start automatic charging as described in the previous chapter
If the battery is so flat that the vacuum cleaner is unable to seek out the charging
station then it is necessary to dock the vacuum cleaner into the charging station
by hand. Grasp the vacuum cleaner and manually place it into the char
so that the charging contacts on the underside of the vacuum cleaner and the
charging contacts on the charging station are connected
connected, charging will start.
The vacuum cleaner can also be charged without using the charging station. Insert
the power adapter connector into socket A5 on the side of the vacuum cleaner and
insert the power adapter plug into amains socket.
CARING FOR THE BA
We recommend tha
battery in acharged state.
Do not leave the vacuum cleaner standing fully charged or completely flat f
unnecessarily long period of time.
A
apermissible level and thereby cause irreparable damage to itself
MEANINGS OF AUDIO AND LIGHT SIGNALS OF
CLEANER
AUDIO SIGNAL
NUMBER OF BEEPS FUNC
3× short beep Stand-by mode
1× short beep Charging
5× short beep Fully charged
1× short beep Setting of scheduled cleaning successful
2× short beep Scheduled cleaning cancelled
4× short beep Low battery voltage
2× short beep Entry into sleep mode
3× short beep Waking from sleep mode
1× long beep
Power c
Error of the front bumper bar or anti-collision switch
Rubber wheels are off the floor or the vacuum cleaner
was lifted
Overloading of the rubber wheels, rotary brush or side
brushes
LIGHT SIGNALS
FLASHING
BUTTON A2 MEANING SOLUTION
red 4× per
second
The dust container is
incorrectly inserted or
is not inserted at all
Check the dust container
Charging error
There was apower outage while the
vacuum cleaner was being charged.
Charging will automatically continue
once power is restor
HOME button on the remote control
or put the vacuum cleaner on to the
charging contacts by hand. Check
that the power adapter is correctly
connected to the charging station
and that the power plug is properly
inserted in apower socket. Start the
charging process again. If the vacuum
cleaner does not start charging, contact
aservice centre.
2× red
1× blue
Anti-collision sensor
error
The anti-collision sensor or the bumper
bar is dirty. Clean the bumper bar
does not help, contact aservice centre.
2× red
2× blue
One of the anti-fall
sensors has detected
an area into which
the vacuum cleaner
could fall.
Move the vacuum cleaner to adifferen
location where there is no risk of afall.
3× red
1× blue
Error on one or both
rubber wheels
Check that the wheel is turning freely
and if necessary remove any dirty
material preventing the mov
the wheel.
1× red
1× blue
Error on the side
brushes
One of the side brushes is jammed due
to dirty material.
Remove any dirt or grime.
1× red
2× blue Central brush error The brush is jammed due to dirty
material. Remove any dirt or grime.
1× red
3× blue Fan mot
The fan motor was overloaded.
container is probably completely full
or the central brush is heavily clogged
with dirty material. Clean out the
vacuum cleaner
Red 2× per
second Low voltage
The battery is almost flat and the
robotic vacuum cleaner is no longer
able to travel to the charg
its own. It is necessary to place it into
the charging station by hand.
TROUBLESHOOTING
Y
that are not indicated by audio or light signals using the f
are unsuccessful resolving the resulting situation, a
on again using the main switch A4 . If the problem persists, please contact an
authorised service centre.
PROBLEM POSSIBLE CAUSE SOL
The vacuum
cleaner cannot be
turned on.
The battery is not inserted
correctly in the robotic
vacuum cleaner
Insert the batter
to the instructions in this
user'smanual.
The battery is flat. Charge the battery.
The vacuum
cleaner is on, but it
is not vacuuming
dust and dirt.
The dust container is full. Empty the dust container
The dust filter is not
properly installed in the
dust container
Properly install the dust filter
into the dust container
The vacuum
cleaner travels
only backwards
when it is turned
on.
The vacuum cleaner was
placed on afloor that is
too dark.
Move the vacuum cleaner to
alighter-coloured floor and
start it again.
An anti-fall sensor is dirty. Clean the anti-fall sensors.
The rotary brushes
are deformed and
do not sweep up
dust and dirt.
The brushes are worn out.
Dip them in warm water to
renew their original shape.
Contact the vendor or service
centre and order new brushes.
