Bedienungsanleitung Sencor SSJ 5050 (Seite 8 von 10) (Englisch)

758817

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

EN-8

Slow Juicer

SSJ 5050SS / SSJ 5051RD

• Do not use the juicer for processing frozen or excessively hard ingredients, e.g. sugar cane.

• Place the ingredients into the feed tube A2 gradually and push through gently with mild pressure.

Do not overﬁll the feed tube A2 and do not push the ingredients in too quickly and with excessive

pressure. The process of separating the juice from the pulp occurs gradually and will not be sped

up by pushing ingredients in quickly.

• To prevent freshly pressed apple juice from turning brown, you can add a little lemon juice.

• To prevent losing valuable minerals, we recommended consuming the juice immediately after it is

pressed.

DISASSEMBLING THE JUICER

1. Before disassembling the juicer, make sure that it is turned off and disconnected from the power

socket. Make sure that all parts that move during operation have stopped moving.

2. Remove the juice jug A0 and the pulp container A9. Take the pusher A1 out of the feed tube

A2.

3. Release both the locking arms Aqa by lifting them upwards and tilting them out towards the juice

collector A6.

4. Rotate the feed tube A2 anticlockwise and take it off the juice collector A6.

5. Take the juice collector A6 with the strainer A4 and the screw shaft A3 located inside off the

base unit Aqd by lifting it upwards.

Note:

It will be easier to take the juice collector A6 off the base unit Aqd when you clean out the pulp

remains after juicing, as described in point 5 in chapter Using the juicer.

6. Over a sink, take the screw shaft A3 and strainer A4 out of the juice collector A6.

CLEANING AND MAINTENANCE

• Clean out the juicer after every use. Before cleaning it, make sure that the juicer is turned off,

disconnected from the power socket and properly disassembled.

• Remove juice and pulp residues from the juice jug A0 and the pulp container A9. Thoroughly

wash both containers A0 and A9, the pusher A1, the feed tube with hopper and lid A2 and the

screw shaft A3 using warm water with kitchen detergent. Then rinse them under clean running

water and thoroughly wipe dry with a ﬁne wiping cloth.

• Thoroughly wash the strainer A4 and the juice collector A6 under warm running water using

kitchen detergent and a ﬁne nylon brush. If you are unsuccessful in cleaning out the small holes

in the strainer A4, soak it ﬁrst in warm water containing lemon juice. Then to ﬁnish off, rinse the

strainer A4 and the juice collector A6 under clean running water and thoroughly wipe dry with

a ﬁne wiping cloth.

Note:

We recommend that all accessories are washed immediately after use. Dried on juice and pulp

residues are far more difﬁcult to remove and may clog the holes in the strainer A4 and thereby

reduce juicing efﬁciency.

All removable parts can also be safely washed in a dishwasher.

• For cleaning the base unit Aqd, use a cloth lightly dipped in a weak solution of water and neutral

kitchen detergent. Then wipe the surface of the base unit Aqd with a clean dampened cloth and

dry thoroughly. Never submerge the base unit Aqd in water or rinse it under running water.

• Do not use abrasive cleaning products, solvents, thinners, etc. Otherwise the surface may be

damaged.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sencor SSJ 5050 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info