Bedienungsanleitung Skytech 3002 (Seite 5 von 10) (Englisch)

603162

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

NOTE: The remote receiver will only respond to the transmitter when the 3-position slide button on the remote receiver is

in the (middle) REMOTE position. If the system does not respond to the battery transmitter on initial use, see LEARNING

TRANSMITTER TO RECEIVER section, and re-check battery positions in the remote receiver.

HEARTH MOUNT

The remote receiver can be placed on the replace hearth or under the replace, behind the control access panel or

louvers. Position where the ambient temperature inside the receiver case does not exceed 130°F. NOTE: The black Slide

Button (included) should be installed on the receiver for Hearth Mount applications.

WIRING INSTRUCTIONS

A qualied electrician or a gas technician who is trained with gas appliances and gas valves that will be operated by this

remote should install the remote control system. Incorrect wiring connections WILL cause damage to the gas valve or

electronic module operating the gas appliance and may also damage the remote receiver.

WIRING MILLIVOLT VALVES

The remote receiver must be connected to the millivolt valve at the

TH & TH/TP (thermostat) terminals on the terminal block on the

millivolt gas valve. Connect 18 gauge stranded or solid wires from

the remote receiver to the gas valve.

Operation of the remote receiver is similar to that of a thermostat in

that both turn the gas valve ON and OFF based on input signals. A

thermostat’s input signals are different temperatures. The remote

receiver’s input signals come from the transmitter.

Connect one black wire to the TH terminal and the other black wire to the TH/TP terminals on the millivolt gas valve. Nor-

mally it does not matter which wires go to which terminal (Fig. 14).

WIRING ELECTRONIC SPARK IGNITIONS

The remote control receiver can be connected, in series, to

a 24VAC transformer to the TR (transformer) terminal on the

ELECTRONIC MODULE. Connect the hot wire from the 24VAC

transformer to either of the wire terminals on the remote receiver.

Connect another wire (not included) between the other receiver

wire terminal and the TH (thermostat) terminal on the

ELECTRONIC MODULE (Fig. 15).

Fig. 14 Millivolt Gas Valve Wiring

Fig. 15 Electronic Spark Wiring

Skytech: 3002

REV. 4-19-12 Page 5

LEARNING TRANSMITTER TO RECEIVER

Each transmitter uses a unique security code. It will be necessary to press the LEARN button on the receiver to accept

the transmitter security code upon initial use, if batteries are replaced, or if a replacement transmitter is purchased from

your dealer or the factory. In order for the receiver to accept the transmitter security code, be sure the slide button on

the receiver is in the REMOTE position; the receiver will not LEARN if the slide switch is in the ON or OFF position. The

LEARN button in located on the front face of the receiver; inside the small hole labeled LEARN. Using a small screw-

driver or end of a paperclip gently press and release the black LEARN button inside

the hole. When you release the LEARN button the receiver will emit an audible

“beep”. After the receiver emits the beep press the transmitter MODE button and

release. The receiver will emit several beeps indicating that the transmitter’s code has

been accepted into the receiver.

The microprocessor that controls the security code matching procedure is controlled

by a timing function. If you are unsuccessful in matching the security code on the rst

attempt, wait 1-2 minutes before trying again – this delay allows the microprocessor to

reset its timer circuitry – and try up to two or three more times.

OFF

REMOTE

LEARN

Fig. 16 Learning

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skytech 3002 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info