680562
26
Zoom out
Zoom in
Vorherige Seite
1/30
Nächste Seite
– 26
t
General information
DANGER!
Never use a hose or high-pressure cleaner to spray down the
drive or the controller housing.
¾ Always disconnect the mains plug prior to working on the drive
mechanism.
¾ Do not use acids or alkalis for cleaning.
¾ Wipe drive clean with a dry cloth as required.
¾ Never put your hand near the door when it is moving or near moving
parts.
¾ There is a risk of persons being crushed or cut by the mechanism or
sharp edges of the door.
¾ Check the mounting screws and bolts of the drive for tightness and
tighten if necessary.
¾ Check the door according to the manufacturer's manual.
Cleaning chains and drive unit rail
7
8
1. Chain (7) or the drive unit rail (8) is very dirty - cleanse it with a clean
cloth.
2. If necessary, lubricate the chain (7) and drive unit rail (8) with a
“conductive” oil. Do not use any grease!
NOTE!
Specied types of oil: Ballistol, WD40 contact spray
Replacing light bulbs
1. Unplug the mains plug from the socket.
2
1
Time
Reset
Radio
LED2
LED1
Time
Reset
Radio
LED2
LED1
2. Take off the lamp cover (1).
3. Unscrew the light bulb (2) by turning it counterclockwise and removing it.
4. Insert new bulb (32 V, 18 W, BA 15s) and turn clockwise until it is locked.
5. Put the lamp cover (1) in place.
Replacing fuse
(warning light connection)
1. Unplug the mains plug from the socket.
1
2
4
3
Time
Reset
Radio
LED2
LED1
Time
Reset
Radio
LED2
LED1
Reset
Radio
LED2
LED1
Reset
Radio
LED2
LED1
2. Take off the lamp cover (1). Unscrew the screws (2) and take off the
cover (3).
3. Upwardly pull the controller circuit board (2) out of the base frame (4).
4. Replace defective fuse.
8
9
10 11
12
7
1
5. Fuse for warning light connection, terminals 11 + 12.
1 A fast-acting fuse.
5
1
3
2
4
Time
Reset
Radio
LED2
LED1
Time
Reset
Radio
LED2
LED1
Reset
Radio
LED2
LED1
Reset
Radio
LED2
LED1
6
6. Put the controller circuit board (1) into the base frame (2) and insert into
the direct connector (3).
7. Put the cover (4) in place and fasten with screws (5). Put on the lamp
cover (6) and lock in place.
Maintenance and care
26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

sommer-duo-vision-650

Suche zurücksetzen

  • Wie kann ich beim Tor schließen das unnötige Stoppen und Reversieren ausschalten, wenn es keine Lichtschranke, Hindernisse und Widerstände gibt? Eingereicht am 18-4-2024 22:19

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sommer Duo vision 650 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Sommer Duo vision 650

Sommer Duo vision 650 Bedienungsanleitung und Installationsanweisung - Deutsch - 30 seiten

Sommer Duo vision 650 Bedienungsanleitung und Installationsanweisung - Holländisch - 30 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info