Bedienungsanleitung Synq SMX-1 (Seite 5 von 43) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

468139

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

ENGLISH USER MANUAL

SYNQ 5/82 SMX-1 DJ-MIxer

CONTROLS ON THE FRONT:

1. MIC INPUT JACK: Combo jack. Accepts either a balanced microphone with an

XLR connector or an unbalanced microphone with 1/4” mono jack. This input is

mainly used as DJ-microphone. The talk over does not affect the signal level of this

input.

2. 3-BAND TONE CONTROL: The frequency of both Mic1 & Mic2 can be controlled

over a +/-12dB range: Treble@13kHz ~ Middle@1kHz ~ Bass@70Hz.

3. CHANNEL FADERS: Used to control the level of each channel. These high quality

faders can be changed by the user, even when the mixer is working! (on another

channel of course ) For instructions, please read the “Changing the faders”

section.

4. MIC ON/OFF/TALK OVER SWITCH: Used to switch the microphones:

 OFF: Both mic1 & mic2 are switched off.

 ON: Both mic1 & mic2 are switched on.

 TALK OVER: mic1 & 2 are switched on; the sound level of all the other

channels will decrease to around -14dB.

5. MIC1 VOL: Used to adjust the input level of micro 1.

6. MIC2 VOL: Used to adjust the input level of micro 2.

7. CROSS FADER: Adjusts the curve of the cross fader:

 LEFT POSITION: you can make a nice, smooth cross fade between 2

channels. Excellent for beat mixing.

 RIGHT POSITION: you can make very sharp “switch like” cuts. Excellent for

scratching and other aggressive mixing techniques.

 POSITIONS INBETWEEN: you can adjust the cross fader curve to your taste.

Any curve between the 2 extremities can be selected.

8. FADER START ON/OFF SWITCH: When you have a compatible CD-player

connected to the fader control connectors, you can control its start/stop (re-cue)

functions with the cross fader of your SMX-1. With this switch you can turn the fader

start control on and off.

9. FADER START INDICATORS: During the Effect mix mode the indicators display

the output of sounds from the channels selected with the CROSS FADER ASSIGN

A OR B buttons.(10)

ENGLISH USER MANUAL

SYNQ 6/82 SMX-1 DJ-MIxer

10.CROSS FADER ASSIGN BUTTONS: The left side of the cross fader is named “A”,

the right side is named “B”. Every input channel has 2 assign buttons, also named

“A” and “B”. You can easily determine if the signal of a certain channel will be

routed to the left or right side of the cross fader, just by pushing the assign button

with the corresponding name: “A” or “B”. The selected button will be lit.

11.CROSS FADER: Used to mix the signals from the 2 channels assigned to A and B

by the cross fader assign buttons.(10)

12.MASTER OUTPUT FADER: Adjusts the output level of the master output.

(Attention: the “trim output” on the back of the mixer can reduce the maximum

output level of the master output fader. Check this trimmer if the maximum output

level is below normal. In this case please also check if the talk over is switched off)

13.ZONE LEVEL: Used to adjust the level of the ZONE output on the rear panel. Its

level is not affected by the master volume (12) and master balance (38). This output

can be used as a second master.

14.CROSSOVER EFFECTS UNIT: To take full advantage of the crossover effects it is

absolutely necessary to connect a compatible CD-player to the fader output

connectors (see previous chapter n°5). The 3 effects give you additional

possibilities for perfect, beat synchronized mixing! Please read the text below to be

sure you fully understand how it works!

IMPORTANT:

 You must put the “fader start on/off switches” (8) in ON-position.

 You must assign two channels to A and B with the assign buttons (10)

15.CROSSOVER EFFECT MODE SWITCH: Used to select the desired crossover

effect mode:

 FADER: In this mode you can use the cross fader to control the crossover

effects and perform start/stop (recue) functions.

 OFF: Crossover effects are disabled.

 AUTO: In this mode you don’t have to use the cross fader: simply push one of

the buttons and the mix will be done automatically in full beat sync!

16.CROSSOVER EFFECT SELECT/START BUTTONS: Used to select the type of

Effect Mix desired, 3 functions (Echo, Zip and Roll) are available:

 ECHO EFFECT: This effect can be used in FADER and AUTO mode:

 FADER MODE: Press the echo effect button and move the cross fader

from one end to the other. A part of the music is sampled and constantly

looped while the volume decreases until the other player starts

automatically. The echo effect is fully beat synchronized. The length of

the loop can be adapted with the “Preset” buttons (24). You can use the

following presets: ¼ ~ ½ ~ 1/1 ~ 2 ~ 4 ~ 8 beats. The effects display

shows the length of the sampled loop.

Hint: If you just move the cross fader a little from the end position, you can repeat a

small portion of the music to the rhythm of the beat. (Depending on the preset you

choose) You can move the cross fader back to the same end position to stop the

repeated soundswithout actually mixingtwo channels.

 AUTO MODE: While the music is playing, press the “echo effect”

button. The music starts playing in a loop while the volume decreases

automatically until the other player starts. The length of the complete

fade over is shown on the effects display. It can be adapted with the

“preset” buttons (24) and/or the “time parameter knob” (33).

Synq SMX-1 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info