Bedienungsanleitung Tecmate Optimate Pro S (Seite 4 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

609531

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

example, with white matter between the plates, plates touching). If mechanical defects are apparent do not attempt to

charge the battery, have it battery professionally assessed.

6. If the battery is new, before connecting the charger read the battery manufacturer’s safety and operational instructions

carefully. If applicable, carefully and exactly follow acid ﬁ lling instructions.

USING THE OPTIMATE PRO-S OR PRO2: PROCEEDING TO CHARGE

For safety reasons, the OptiMate output will only activate if a battery retaining at least 2V is connected, whereupon the

micro processor instantly diagnoses the battery condition and engages the appropriate charge mode and lights the

corresponding charge status LED.

The charger’s special recovery mode cannot engage if it senses that the battery is still connected to a vehicle wiring

circuit which effectively offers a lower electrical resistance than the battery on its own. However, if the deep-discharged

battery is not removed for recovery, neither battery nor vehicle electronics will be damaged.

VERY FLAT NEGLECTED BATTERIES: Pay particularly close attention to the following which is especially

important for relatively small batteries such as those used on motorcycles, lawn tractors, jet-ski’s, snowmobiles and

similar: A battery left deep-discharged for an extended period may develop permanent damage in one or more cells. Such

batteries may heat up excessively during high current charging.

Monitor the battery temperature during the ﬁ rst hour, then hourly there-after. Check for unusual signs, such as bubbling or

leaking electrolyte, heightened activity in one cell compared to others, or hissing sounds. If at any time the battery is

uncomfortably hot to touch or you notice any unusual signs, DISCONNECT THE CHARGER IMMEDIATELY.

The LED indicators referred to below, and the clauses dealing with them, are sequenced as they may come on through

the course of the programme.

LED #7

LED #8

LED #9

LED #6

LED #5

LED #1

LED #7

LED #8

LED #9

LED #6

LED #5

LED #1

OptiMate PRO2

LED #2

LED #1

LED #3

LED #4

LED #8

LED #7

LED #9

LED #5

LED #6

Optimate PRO-S

IMPORTANT SWITCH SELECTIONS PRIOR TO USING THE CHARGER: PROGRAMME OUTLINE

• A switch to select the input voltage for 115 or 230 Volts is located at the back of the charger. Make sure the input

voltage setting is correct for your AC electrical supply before making any connections.

• OptiMate PRO-S only: Make the appropriate output selection before charging. The NEW LED #1, 2A LED #2 or 4A LED #3

will indicate the chosen selection once the charger is powered up.

NEW - Select for the ﬁ rst activating charge of a new battery and before installing into a vehicle. The NEW programme

(LED #1) disables recover charge (stage 5) and limits charging to 60 minutes for programme stages 6.1 to 6.3 and

also limits testing to a single 10 minute period after which the MAINTENANCE CHARGE CYCLE continues until the

battery is disconnected.

NOTE: A new battery has been successfully activated once LED #7 indicates steadily.

2A / 4A - Select the appropriate maximum charge current (2 / 4A) from the table on the front of the charger’s enclosure

for USED batteries (or NEW batteries that may have been stored for extensive periods following activation) - The 2A /

4A programme limits charging to 12 hours for programme stages 5.1 through 6.3. Thereafter the voltage retention

tests and battery maintenance charging (LED #7,8,9) programme continues until the battery is disconnected.

• OptiMate PRO-2 only: No charge selection is required. The programme limits charging to 48 hours for programme stages

5.1 through 6.3.Thereafter the voltage retention tests and battery maintenance charging (LED #7,8,9) programme continues

until the battery is disconnected.

CONNECTION TO THE INPUT (WALL SOCKET) AND SWITCHING ON THE CHARGER: Attach the power cord to

the charger via the power receptacle at the back of the charger, and insert the power plug into the wall socket (and switch on

the socket outlet if applicable). The charger’s on-off switch is located at the back of the charger.

1. 2. 3. When switched on, for the OptiMate PRO-S model one of the current selection LEDs #1, or 2, or 3, will indicate. For

the OptiMate PRO2 the power indicators (LEDs #1 and 2) for both charging circuits, will light and all CHARGE and TEST LEDs

(LEDs #5 to 9) will ﬂ ash twice brieﬂ y to conﬁ rm micro processor health. If not, check the AC supply and the power cord. If for

any reason the input protection fuse located in the base of the charger should fail, replace it only with a similar new fuse of

identical type and 3 Amp rating.

4. If the battery connections are inverted, no charge or test status LEDs will light following the micro processor health

conﬁ rmation. For OptiMate PRO-S only: The inverse polarity LED #4 will light. Both models: The charger is automatically

protected against this error and no damage will result. Disconnect at the battery and reconnect correctly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tecmate Optimate Pro S Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info