Bedienungsanleitung TFA 35.1045.IT - Laluna Funk (Seite 13 von 16) (Englisch)

466142

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

The bar chart indicates the air pressure history trend over the last 24 hours in 7 steps, 0h, -

3h, -6h, -9h, -12h, -18h, and -24h. The “0h” represents the current full hour air pressure

recording. The columns represent the “hPa” (0, ±2, ±4, ±6) at specific time. The “0” in the

middle of this scale is equal to the current pressure and each change (±2, ±4, ±6) represents

how high or low in “hPa“ the past pressure was compared to the current pressure.

If the bars are rising it means that the weather is getting better due to the increase of air

pressure. If the bars go down, it means the air pressure has dropped and the weather is

expected to get worse from the present time “0h“.

Note:

For accurate barometric pressure trends, the Weather Station should operate at the same

altitude for example, it should not be moved from the ground to the second floor of the

house. Should the unit be moved to a new location, discard readings for the next 12-24

hours.

OUTDOOR TEMPERATURE/HUMIDITY DATA

The fourth LCD section shows the outdoor temperature and humidity, the reception indicator,

the transmitter identification number and the MIN/MAX outdoor data.

TOGGLING AND RESETTING THE OUTDOOR DATA

To toggle between the outdoor current, MAX/MIN temperature and humidity data and

the times (for temperature data only) they were recorded press the OUT/+ key:

Once to show the MAX outdoor temperature and humidity data with the recorded

time and date.

Twice to show the MIN outdoor temperature and humidity data with the recorded

time and date.

Three times to return to the current displayed values.

2. Once the MIN or MAX data is displayed, press and hold the SET key for 3 seconds to

reset the respective MIN or MAX record to current temperature and humidity data, and

current time, date display.

Note: The MIN or MAX data needs to be reset individually.

TO VIEW THE MIN/MAX DATA FROM DIFFERENT TRANSMITTERS

When more than 1 transmitter used:

1. To toggle between transmitters, press the SNOOZE/CH key:

Once to show transmitter 2

Twice to show transmitter 3

Three times to return to transmitter 1

2. Use OUT/+ key to view the MIN/MAX temperature and humidity data for the selected

transmitter.

3. To reset the minimum and maximum temperature and humidity data, and the times at

which they were recorded, press the SET key continuously for about 3 seconds. This

will reset the MIN/MAX data recorded to the current time, date, temperature and

humidity. The current time taken is the normal displayed time and does not regard the

time zone set for the unit.

Note: the MIN/MAX data for each transmitter needs to be reset separately.

Outdoor

temperature in

°C/ °F

Outdoor relative

humidity in RH%

Outdoor transmitter identification number

MIN icon

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

TFA 35.1045.IT - Laluna Funk Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von TFA 35.1045.IT - Laluna Funk

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info