Bedienungsanleitung Triton T12ID (Seite 7 von 50) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

665019

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

OPERATING INSTRUCTIONS

Re-charging the battery

• After use, a lithium-ion battery must be allowed to cool

down before charging

• If a hot battery is inserted into the charger both LEDs

will illuminate. The charger will begin to charge when

the battery has cooled sufﬁciently (this may take

several minutes)

Installing the battery

• The battery should ﬁt easily into the battery charger or

impact driver unit. If the battery is difﬁcult to ﬁt, check

the condition of the battery and contacts

Battery - length of service

The length of service from each charging cycle will depend

on the type of workload. The battery charger and battery

for this drill have been designed to provide a long trouble-

free working life. The charger intelligently monitors the

condition of the battery and selects the ideal charging rate

for the condition of the battery. It protects the battery from

over-charging or charging at too high a rate. However, like

all batteries, performance will be reduced over time.

To maximise battery life:

• Store and charge the battery in a cool area.

Temperatures above or below normal room temperature

will reduce battery life

• Never store lithium-ion batteries in a discharged

condition. Recharge them immediately after they are

discharged. For storing long term, store fully charged

• All batteries gradually lose their charge, even lithium-

ion batteries, but the discharge rate is very low. If

the drill is stored for long periods of time without use,

recharge the battery every three to four months and

disconnect the battery from the power tool before it is

stored. This practice will prevent the lithium-ion battery

from becoming damaged if left fully discharged for a

long period of time

• Warning: Never ﬁt any attachment with a maximum

speed lower than the no load speed of the machine.

NOTE: Wear gloves when handling bits or accessories

which are sharp or remain hot after use

Fitting a driver bit

1. Pull the Quick Release Mechanism (2) forward and

insert the bit into the quick release 6mm / ¼" Hex Drive

(1)

2. Release the quick release mechanism

3. Pull on the bit to check that it is securely ﬁtted. If the bit

is not secure, repeat the above procedure

NOTE: Make sure screwdriver bits used are hardened and

suitable for use with an impact driver

Direction control

• The direction of rotation can be set using the Forward/

Reverse Selector (3)

• To rotate the impact driver clockwise, push the forward/

reverse selector to the left

• To rotate the impact driver anti-clockwise, push the

forward/reverse selector to the right

• When the forward/reverse selector is in the central

position, the impact driver is locked

• Do not attempt to move the forward/reverse selector

when the tool is running

Switching on

• To start the impact driver, squeeze the Trigger Switch

(6). The LED Guide Light (7) will illuminate automatically

• Further pressure on the trigger will increase the running

speed of the tool

• Practice using the impact driver before using it for

normal applications

NOTE: It is possible the impact driver may switch off

during heavy use due to thermal protection of the battery

and internal components. This may prevent the tool being

used again for a short period of time and doesn’t represent

a fault

725488_Z1MANPRO1_15/04/14.indd 7 18/09/2015 15:11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Triton T12ID Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info