756403
7
Zoom out
Zoom in
Vorherige Seite
1/10
Nächste Seite
EN 7
pyrometer BP21
Storage
When the device is not being used, observe the following
storage conditions:
dry and protected from frost and heat
protected from dust and direct sunlight
with a cover to protect it from invasive dust if necessary
The storage temperature is the same as the range given in
the Technical data chapter.
Remove the batteries from the device.
Preferably use the supplied device bag to store the device.
Operation
Inserting the battery
Note
Make sure that the surface of the device is dry and the
device is switched off.
23
22
1. Open the battery compartment by folding open the
cover(23) with your fingers.
2. Use the battery clip(22) to connect the new battery with
correct polarity.
3. Insert the battery in the battery compartment.
4. Close the cover of the battery compartment.
Carrying out a measurement
Info
Please note that moving from a cold area to a warm
area can lead to condensation forming on the device's
circuit board. This physical and unavoidable effect can
falsify the measurement. In this case, the display
shows either no measured values or they are incorrect.
Wait a few minutes until the device has become
adjusted to the changed conditions before carrying out
a measurement.
Ensure that the surface to be measured is free of dust, dirt
or similar substances.
To be able to gain exact measurement results on surfaces
which reflect heavily, stick matt masking tape to the
surface or apply matt black paint with a very high and
known degree of emission.
Note the 12:1 ratio of the distance to the measuring spot
size. For accurate measurements the measuring object
should be at least twice as large as the measuring spot.
1. Point the device at the object to be measured.
2. Press the measurement button(6).
ðHold onto the measurement button(6) if you want to
perform a prolonged measurement.
ðThe device turns on and carries out a measurement.
The SCAN indication(17) appears on the display.
ðThe current measured value is displayed in the
measurement value display(16).
3. Let go of the measurement button(6) again.
ðThe device stops measuring. HOLD(18) appears on the
display. Depending on the setting of the device, either
the maximum or minimum value of the last
measurement cycle will be shown in addition.
ðThe device switches off after approx. 8seconds.
7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Trotec BP21 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Trotec BP21

Trotec BP21 Bedienungsanleitung - Deutsch - 10 seiten

Trotec BP21 Bedienungsanleitung - Holländisch - 10 seiten

Trotec BP21 Bedienungsanleitung - Französisch - 10 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info