Bedienungsanleitung Truma Ultrastore Rapid GE (Seite 9 von 16) (Englisch)

631208

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Choice of location

Always install the appliance in such a way that it is easily

accessible for service work at all times and can be easily

removed and installed.

Locate the heater in such a way that the cowl can be mounted

on the outside on a surface which is as straight and smooth

as possible. This outside surface must be exposed to wind

from all directions and, if possible, there should be no trim

strips or covers in this area, mount heater on an appropriate

base, if necessary.

The cowl may not be positioned within 500 mm (A) of a refu-

elling point or fuel tank breather outlet or within 300 mm (A)

of a ventilator for the living space. If the cowl is positioned

vertically below an opening part of a window, the water heater

must be fitted with an automatic shut-off device (please refer

to page 14) to prevent operation when the window is open.

Window

Floor

300 mm

Prohibited

Zone

Prohibited

Zone

The heater must not be installed close to or directly behind a

room / space heater.

To achieve reasonable air flow for electronics cooling,

there should be a minimum distance of 20 mm between the

electronics cover (34) and the walls of the furniture piece

the Ultrastore is located in.

Installation of the water heater

Position template for cowl opening on the inside of the wall.

A = bottom edge of heater

B = lateral edge of heater

Drill 4 holes (C) with 10 mm dia. through the wall. Drill hole (E)

with 15 mm dia. for condensation pipe (also possible from the

outside = F).

Position template on the outside of the wall. The markings (C)

must be above the through-holes. Saw cut-out section for

cowl (D) 92 x 168 mm.

If the distance between outside wall and heater is more than

35 mm you must use the cowl extension VBO 2 (please refer

to page 14) with an additional length of 50 mm. Saw out

100 x 176 mm along the dashed line.

rea cut-away

for clarification

If there are any cavities in

the area of the cowl, pack

these with pieces of wood

so as to be able to tighten

the screws. The finished

hole should be 168 mm high

and 92 mm wide.

Cut out trim strips or such on the vehicle or place supports

beneath them so as to make the cowl lie flat.

Place a support beneath the heater if the walls are sloping.

An angle of inclination of 10 degrees is not to be exceeded.

Installation instructions

Installation and repair are only to be carried out by an

expert. Always read and follow the operating instructions

carefully prior to starting any work!

Non-compliance with installation instructions or

incorrect installation can result in endangerment

of persons and property.

Intended use

This appliance has been designed for the installation in cara-

vans, motor homes and other vehicles. It is not approved

for installation in boats. Other forms of use are also possible

following consultation with Truma.

Information regarding boats: For installation in boats Truma

supplies the DVGW-tested boat water heater.

Regulations

Any modifications to the unit (including the exhaust duct and

the cowl) or the use of spare parts and accessories that are

important to the operation of the system (e.g. the time switch)

that are not original Truma parts and failure to follow the in-

stallation and operating instructions will cancel the warranty

and indemnify Truma from any liability claims. It also becomes

illegal to use the appliance, and in some countries this even

makes it illegal to use the vehicle.

In-vehicle installations must comply with the technical and

administrative regulations of the respective country of use

(e.g. EN 1949 for vehicles). The national regulations and rules

must be complied with.

Water heater kit

The water heater kit contains

1 Assembled water heater

1 Cowl assembly with screws

1 Hot water connector

1 Cold water connector

1 Safety (pressure relief) drain valve

1 Wall switch (gas operation) with 3 m cable

1 Wall switch (230 V operation)

1 Installation template

1 Set literature

1 Label with warning information

In order to guarantee complete emptying of the water con-

tent, ongoing sealing tightness of the water connections and

safety function all enclosed parts must be used!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Truma Ultrastore Rapid GE Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info