Bedienungsanleitung Truma Ultrastore Rapid GE (Seite 10 von 16) (Englisch)

631208

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Insert heater with cowl body (1) through the wall cut-out (2),

allow approx. 5 mm to project out of the wall. Mount sealing

frame (3) (the anti-twisting device ensures correct fitting!).

Pre-drill holes for the 6 fastening bolts (4).

Remove sealing frame (3) and coat with non hardening mastic

on the side facing the vehicle – do not use silicone!

The sealing frame must be well sealed with respect to

the front sides and the cross bars of the cowl body (1)

as well as towards the outside wall!

Fasten sealing frame (3) to the cowl body using 4 self-cutting

screws (4).

Screw the sealing frame (3) in contact together

with the cowl body (1) so the anti-twist device

projects out!

Seal the gap between the hole (6) and the condensation

tube (7) with non hardening mastic – do not use silicone!

Mount the grille (8). Press the entire cowl assembly onto the

vehicle wall and fasten with 6 screws (5).

Screw the water heater securely to the floor of the vehicle

with at least two shackle plates (9) with the screws provided,

B 5.5 x 25, on suitable base (plywood panel, laminated wood

strips or metal base).

Water connection

All pressure and submergible waterpumps up to 2.8 bar

and all mixed combination sets with or without an electrical

switch, can be used for operating the water heater.

If connecting to a central water supply (rural or city con-

nection) or when using more powerful pumps, a pressure

reducer must be used which prevents pressures of greater

than 2.8 bar occurring in the system.

When using submergible pumps, a non-return valve (10 – not in-

cluded in the scope of supply) must be fitted between the pump

and the first branch point (arrow points in direction of flow).

When using pressure pumps with high switching hysteresis,

hot water may flow back through the cold water tap. To pre-

vent the backflow, we recommend that a non-return valve

(11 – not included in the scope of supply) be fitted between

the outlet to the cold water tap and the drain valve.

When using the Truma Ultrastore together witch the

Truma Ultraflow pressure switch, the use of a non-re-

turnvalve is essential (please refer to the pressure switch

instruction).

In order to guarantee complete emptying of the water

content and ongoing sealing tightness of the water

connections, the enclosed water connectors (12 + 13) and

the safety (pressure relief) drain valve (14) must be used!

John Guest System rigid pipe routing

The water connectors (12 + 13) and safety/drain valve (14)

supplied with the Truma Ultrastore have a 12 mm diameter

fitting and are only approved to use with Original John Guest

piping.

For connecting to rigid pipes with other diameters appropiate

adapters (not included in scope of delivery) must be used.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Truma Ultrastore Rapid GE Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info