Bedienungsanleitung Vortex Viper Riflescope (Seite 2 von 4) (Englisch)

540499

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Side Focus

Parallax

Adjustment

Dial

Setting the side focus parallax adjustment dial on the Viper PA scopes is very easy.

Parallax Adjustment on PA Models

A. Be sure that the reticle is properly focused.

B. Match the range number (distance you are shooting) on the objective lens barrel as closely as possible to the indicator arrow on the

riflescope body.

C. Check the setting by moving your head up/down and left/right while looking through the scope. The setting is correct if there is

no apparent movement between the reticle and target. If there is movement, continue adjusting the lens slightly until the movement

is eliminated.

Riflescope Installation

To get the best results from your Viper riflescope, proper mounting is essential. Although not extremely difficult, the correct steps must be

followed. If you are unsure of your abilities, it would be best to use the services of a qualified gunsmith.

Your Viper riflescope is pre-set at the factory with the reticle

centered in both adjustment ranges. This is the ideal position to

begin sight-in. If you have changed the settings and wish to

re-center the reticle, follow this procedure:

1. Centering the Reticle

A. Turn either dial (windage or elevation) as far as you can in one

direction until it stops.

B. Turn the dial in the other direction until it stops, carefully

counting the audible clicks as you turn the dial.

C. Turn the dial back again to half the number of clicks counted in

Step B—the reticle will be centered for that adjustment only.

D. Repeat for the other adjustment so that the reticle is centered

in both the windage and elevation settings.

Using high quality, appropriately sized rings* and bases matched

to your rifle, mount the scope as low as possible on the rifle. A

low mounting will help assure proper cheek weld and aid in a

solid shooting position and fast target acquisition. We recommend

using the lowest rings that will give complete clearance of scope

and rifle. Avoid contact with barrel, receiver, bolt handle, or any

other part of the rifle. Work the riflescope’s zoom ring and rifle’s

action to assure no contact. Be sure to follow the manufacturer

instructions supplied with the rings and mounting base.

2. Mount As Low as Possible

*Standard Vipers use 1-inch rings; select PA models use 30mm.

3. Adjust for Maximum Eye Relief

Before final the tightening of the riflescope rings, adjust for

maximum eye relief to avoid injury from recoil.

A. With the riflescope set at the lowest magnification, slide

the scope as far forward as possible in the rings.

B. While viewing through the scope in the normal shooting position,

slowly slide the scope back towards you. When you feel you

just

hit the full field of view, stop. Without disturbing the front-back

setting, slowly rotate the scope until the elevation dial is at the top

of the scope and the vertical crosshair of the reticle matches the

vertical axis of the rifle. Using a visual vertical reference such as the

edge of a building or telephone pole can help with this.

B. Tighten the rings per the manufacturer’s instructions.

Initial bore sighting of the scope at short range of 50 yards will

save time and money at the shooting range. This can be done

using a bore sighter, following the manufacturer’s instructions,

or by removing the bolt and sighting through the barrel on a

bolt action rifle. With the rifle placed solidly on a bench and

the bolt removed, sight through the bore and center the target

inside the the barrel. With the bulls-eye centered in the bore,

make windage and elevation adjustments until the reticle

crosshair is also centered over the bulls-eye. If possible, make

initial windage adjustments using the mounting base rather than

the riflescope’s windage dial.

4. Bore Sighting

5. Base Adjustments and Shimming

If large windage/elevation corrections have been made using bases or shims, it

will be necessary to have the rings lapped. Consult a qualiﬁ ed gunsmith if you’re

unsure of this procedure.

Note:

Vortex riflescopes come centered from the factory, but you will

need to make some adjustments when initially sighting in your

scope. Many ring and base setups allow you to adjust windage

at the base mount. If possible, use these adjustments for initial

windage change. Though not usually necessary, you can correct

the elevation adjustments using shims under the base mount.

Assuming typical ring spacing of 3.25”, a shim of .001”

will yield 1” at 100 yards, 2” at 200 yards, and so on.

Shim under the front base for more down adjustability and under

the rear base (nearest shooter) for more up adjustability. Please

consult a qualified gunsmith if you are unsure of this procedure.

www.vortexoptics.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vortex Viper Riflescope Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info