809800

VTech LM808-1W Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
Status icons
Connection status
• displays when strong signal strength is detected between the baby unit
and the parent unit.
• or displays when moderate or low signal strength is detected between
the baby unit and the parent unit.
• displays when weak signal strength is detected between the baby unit and
the parent unit.
Lullaby
• Displays when the baby unit being viewed is playing lullaby.
Current view status
Night vision
• Displays when the baby unit being viewed has activated the night vision feature.
Zoom
• Displays when the current image on the parent unit has zoomed in.
Temperature alert tone
• Displays when the temperature alert tone is set on.
oF or
oCReal-time temperature
• Displays the real-time temperature detected by the baby unit in Fahrenheit (oF)
or Celsius (oC) (e.g. 57
oF or 14
oC).
Mute alert
• Displays when the parent unit speaker volume is set to off.
• Displays when the parent unit is talking to the baby unit.
Below are the questions most frequently asked about the baby monitor.
Why does the
baby monitor
not respond
normally?
Try the following (in the order listed) for common cure:
1. Disconnect the power to the baby unit and the parent unit.
2. Remove the batteries in the parent unit. Then, install the batteries again.
3. Wait a few seconds before connecting power back to the baby unit and the parent unit.
4. Turn on the baby unit and the parent unit.
5. Wait for the parent unit to synchronize with the baby unit. Allow up to one minute for
this to take place.
Why doesn’t the
baby unit and parent
unit power-on light
illuminate when the units
are switched on?
Perhaps the parent unit is not connected to the power. Insert the appliance plug into the
parent unit and insert the adaptor in a wall socket. Then, press and hold POWER to switch
on the parent unit and to establish connection with the baby unit.
Perhaps the baby unit is not connected to the power. Insert the appliance plug into the
baby unit and insert the adaptor in a wall socket. Then, slide the ON/OFF switch to ON
to switch on the baby unit and to establish connection with the parent unit.
Why doesn’t my parent
unit charge while
connected to AC power?
Make sure the power is not controlled by an electronic wall switch.
Make sure the battery is correctly installed in your parent unit.
Why is my screen in black
and white? The screen is in black and white during night-time or in a dark room when the night
vision feature is activated. This is normal.
Why do I get glare or
blurry display on my
screen when viewing my
baby at night?
During night-time or in a dark room, the surroundings and other interfering factors, like
lighting, objects, colours and backgrounds may affect the image quality on your parent
unit screen. Adjust the baby unit angle or place the baby unit at a higher level to prevent
glare and a blurry display.
Why does the baby
monitor produce a
feedback?
The parent unit and baby unit may be too close to each other.
• Move the parent unit away from the baby unit until the noise stops; OR
• Turn down the volume of your parent unit.
Why does the parent unit
beep? The baby unit may be out of range. Move the parent unit closer to the baby unit (but not
less than 1 metre).
The parent unit may not have enough charge for the parent unit to perform normally.
Charge the battery in the parent unit until battery icon become solid.
The temperature of your baby’s room may be too high or too low.
Why does the parent unit
react too quickly to other
sounds?
The baby unit also picks up other sounds than those of your baby. Adjust the VOX
sensitivity level to a lower level or lower the parent unit speaker volume.
Why don’t I hear a sound/
Why can’t I hear my baby
cry?
The parent unit speaker volume may be too low. Press to increase the volume.
You may have set a low VOX sensitivity level. See Adjust the sound sensitivity of the baby
unit to set to a higher level.
Frequently asked questions
When you are not going to use the baby monitor for some time, remove the rechargeable battery from the
parent unit. Store the parent unit, the baby unit and the adaptors in a cool and dry place.
Storage
1 LED lights
Indicate the different statuses of the
parent unit. For details, refer to Parent
unit lights.
2LCD display
3VOL
4 VOL
5 Zoom
• Press to zoom in or out.
6VIEW / LCD ON/OFF
7Microphone
8POWER
9TALK
• Press and hold to talk to the selected
baby unit.
10
• While in a menu, press to return to
the main menu or idle screen.
• While viewing zoomed image,
press and hold to move the zoomed
image leftward.
11
• While in a menu, press to scroll up.
• While viewing zoomed image,
press and hold to move the zoomed
image upward.
12
• While in a menu, press to choose an
item.
• While viewing zoomed image,
press and hold to move the zoomed
image rightward.
13 MENU/SELECT
• Press to enter the menu.
• While in a menu, press to choose an
item, or save a setting.
14
• While in a menu, press to scroll down.
• While viewing zoomed image,
press and hold to move the zoomed
image downward.
15 Antenna
16 RESET
• Force reboot the parent unit.
17 Stand
18 Speaker
19 Power jack
EXIT
1Microphone
2Camera
3Light sensor
4ON/OFF LED light
• On when the baby unit is turned on
and is paired to the parent unit.
• Flashes when the baby unit is not
being viewed;
or when the link to the parent unit is
lost.
5Infrared LEDs
6Pair hole
• Your baby unit and parent unit
provided are already paired.
7Speaker
8Temperature sensor
9 ON/OFF switch
• Slide to turn on or off the baby unit.
10 Power jack
11 Wall mount holes for upright
mounting
12 Wall mount holes for lateral mounting
• While in a menu, press to return to
the main menu or idle screen.
Caution
• Do not install the baby unit at a
height above 2 metres.
Baby unit overview
11
12
Main menu icons
Brightness
• You can change the brightness of the parent unit screen.
Camera settings
• You can adjust the baby unit’s speaker volume.
Lullaby
• With this feature, you can select one of the soothing sounds, or white noise.
• you can select one of the five melodies, or play all melodies
• you can set timer to stop playing the selected melody or soothing sound.
Night light
• you can turn on or off the night light.
• you can select one of the night light colours.
• you can set timer to turn the night light off.
• you can set to auto turn on the night light when baby unit detects sound. It will
turn off after 15 minutes of no sound detection. You can set VOX sensitivity level to
detect sounds that exceed certain levels. See Turn on or off the sound activation
section.
Temperature
• You can choose to set the maximum/ minimum temperature and turn on the
Temperature alert tone, so that the parent unit beeps whenever the room
temperature detected by the baby unit falls outside of the desired temperature range.
• You can choose to display the temperature in Fahrenheit (oF) or Celsius (oC) on your
parent unit.
Alert Tone
• You can set the parent unit to beep when:
the parent unit operates in low battery condition;
the link between the parent unit and the baby unit is lost;
when selecting an option in the menus.
• You can turn on/off the alert vibration.
Sound-activated Screen
• When the baby unit detects no sound, the parent unit screen remains off to save
power. Once a sound is detected, the parent unit screen turns on automatically. It
will then turn off again after 50 seconds of no sound detection.
VOX Sensitivity
• You can set VOX sensitivity level to activate parent unit screen and sound when
baby unit detects sounds that exceed certain levels. See Turn on or off the sound
activation section.
Parent unit overview Parent unit lights
LINK • On when the parent unit is linked to the baby unit.
• Flashes when the link to the baby unit is lost.
• On when the parent unit is connected to AC power, or the battery is charging.
• Flashes when the parent unit battery is low and needs charging.
• Off when the parent unit is disconnected from AC power.
It turns on:
• When the parent unit speaker volume is set to off; or
• When the parent unit is talking to the baby unit.
TALK • On when the parent unit is talking to the baby unit.
19
The baby unit has infrared LEDs that allow you to see your baby clearly at night or in a dark
room. When the baby unit being viewed detects low light levels, the infrared LEDs are
switched on automatically. The images from the baby unit are in black and white, and
appears on the screen.
Notes
• It is normal if you see a short white glare on your parent unit screen as the baby unit adapts to the
dark environment.
• When the infrared LEDs are on, the images are in black and white. This is normal.
Tip
• Depending on the surroundings and other interfering factors, like lighting, objects, colours and
backgrounds, the video quality may vary. Adjust the baby unit angle or place the baby unit at a higher
level to prevent glare and blurry display.
Night vision
To keep this product working well and looking good, follow these guidelines:
• Avoid placing it near heating appliances and devices that generate electrical noise (for example, motors or
fluorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft damp cloth.
• DO NOT immerse the parent unit and the baby unit in water and do not clean them under running water.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the baby unit and parent unit are dry before you connect them to the mains again.
General product care
3. Press or to choose Temperature Alert tone, then press .
4. Press or to choose On or Off, then press to confirm your selection.
Temperature format
You can choose to display the temperature in Fahrenheit (oF) or Celsius (oC).
1. Press when the parent unit is idle.
2. Press or to choose Temperature.
3. Press or to choose Format, then press .
4. Press or to choose oF or oC, then press to confirm your selection.
3
Using the baby monitor (Cont’d)
Mount the baby unit on dry wall (optional)
Items to purchase
You will need to purchase the
following items separately to
mount your baby unit:
Use a pencil to mark two holes in
parallel. Make sure they are the same
distance apart as the wall mount holes
on the baby unit.
NOTESNOTE
Note
• Check for reception strength and camera
angle before drilling the holes.
2 screws
2 anchors
Drill two holes in the wall.
If you drill the holes into a stud, go to
step 3.
-OR-
If you drill the holes into an object other
than a stud, insert the wall anchors into
the holes. Tap gently on the ends with a
hammer until the wall anchors are flush
with the wall.
Insert the screws into the holes and
tighten the screws until only 6mm of the
screws are exposed.
Depending on your preference, choose
the upright or lateral orientation to mount
your unit. Align the wall mount holes at the
bottom or at the rear side of the baby unit
with the screws on the wall. Slide the baby
unit down until it locks into place.
OR
Tilt or rotate to adjust camera angle.
OR
NOTESNOTE
Note
• The types of screws and anchors you
need depend on the composition of the
wall.
Customer service and product warranty
Why can’t I establish a
connection? Why is the
connection lost every now
and then? Why are there
sound interruptions?
The baby unit may be out of range. Move the parent unit closer to the baby unit (but not
less than 1 metre.
Other electronic and wireless products may cause interference with your baby monitor.
Try installing your baby monitor as far away from these devices as possible.
If you power on only one baby unit, your parent unit may display and No link to CAM #,
and the LINK LED light flashes. Press VIEW to switch to the baby unit you have powered on.
Parent unit icons
Warning icons and messages
No link between units The connection between parent unit and baby unit is lost.
Battery low at Parent Unit The battery level of the parent unit is very low and needs
to be recharged.
Temperature too high at
Baby unit
or
Temperature too low at
Baby unit
The temperature detected by the baby unit is higher/
lower than the desired temperature alert range.
9-level sound indicator
• (1 to 3 bars) indicates low sound level detected by the baby unit.
• (4 to 6 bars) indicates moderate sound level detected by the baby unit.
• (7 to 9 bars) indicates high sound level detected by the baby unit.
Speaker volume
• Displays the parent unit speaker volume level while adjusting.
Battery status
• animates when the battery is charging.
• displays solid when the battery is fully charged.
• displays when the battery is low and needs charging.
Night light (On)
• Displays when the night light is on.
Night light (Auto-On)
• Displays when the night light is on Auto mode.
• Color icon indicates the night light is set to auto-on, and is currently turned on
by sound activation.
• Gray icon indicates the night light is currently off but is set to auto-on. Night
light will turn on when sound is detected by the baby unit.
Projection light (On)
• Displays when the projection light is on.
Projection light (Auto on)
• Color icon indicates the projection light is set to auto-on, and is currently turned
on by sound activation.
• Gray icon indicates the projection light is currently off but is set to auto-on.
Projection light will turn on when sound is detected by the baby unit.
Alert vibration
• Displays when the alert vibration is on.
IMPORTANT
Please retain this booklet with your sales receipt as proof of the date of purchase.
Customer Service
Please call our Consumer Services Department on 03306 780149 (from UK) or
+44 3306 780149 (outside UK) and a service representative will be happy to help you.
Declaration of Conformity
The crossed-out wheelie bin symbols on products and batteries, or on their respective packaging,
indicates they must not be disposed of in domestic waste as they contain substances that can be
damaging to the environment and human health.
The chemical symbols Hg, Cd or Pb, where marked, indicate that the battery contains more
than the specified value of mercury (Hg), cadmium (Cd) or lead (Pn) set out in Battery Directive
(2006/66/EC).
The solid bar indicates that the product was placed on the market after 13th August, 2005.
Help protect the environment by disposing of your product or batteries responsibly.
Disposal of batteries and product
This product is intended for use within Europe and UK.
This equipment complies with the essential requirements to EU’s Radio Equipment
Directive (2014/53/EU) and the UK’s Radio Regulations 2017 on radio systems and
telecommunication equipment.
VTech Telecommunications Ltd. hereby declares that
this Video Monitor LM808-1W is in compliance with the essential requirements and
other relevant provisions of EU’s Radio Equipment Directive (2014/53/EU) and UK’s Radio
Equipment Regulations 2017.
The Declaration of Conformity for the LM808-1W is available from
www.vtechbabycare.com.
Manufacturer: VTech Telecommunications Ltd.
23/F., Tai Ping Industrial Centre, Block 1, 57 Ting kok Road, Tai Po, Hong Kong.
Importer: VTech Electronics Europe Plc
Napier Court, Abingdon Science Park, Abingdon, Oxon, OX14 3YT, U.K.
This warranty is valid for the UK and Ireland only. For products purchased outside
the UK and Ireland, please contact your local distributor or place of purchase.
P
R
O
D
U
C
T
W
A
R
R
A
N
T
Y
ONE
YEAR
PRODUCT WARRANTY
Thank you for choosing this quality product from VTech.
1.The product detailed above is covered by a one year warranty from the date of purchase,
against any defects in materials or workmanship.
2.The product may be returned to the place of purchase. Alternatively the product can be
returned to VTech Electronics Europe Plc (see address below), with proof of purchase,
without proof of purchase no replacement will be provided.
3.VTech Electronics Europe Plc will examine the product and if it is found to be defective
due to faulty materials or workmanship, will replace the product at their discretion.
4.If the product covered by this warranty is damaged due to misuse, modification or
unauthorized repair, or because of faulty batteries, battery discharge or incorrect
electrical connections, then this warranty becomes void.
5.This warranty is personal to the original purchaser and is not transferable.
6.Breakages to the LCD screen are not covered by the warranty.
7.Products returned to VTech Electronics Europe Plc, should be sent to the address shown
below and packed carefully to avoid damage in transit. Please do not include batteries or
adaptors. Please include details of the fault together with your name and address,
contact phone number and/or email address.
8.To keep an online record of your warranty, please register your product online at
www.vtech.co.uk/clubvtech
VTech Electronics Europe Plc, c/o XPO Logistics, Warehouse 350, Cat & Fiddle Lane,
West Hallam, DE7 6HE
THIS WARRANTY IS OFFERED AS AN EXTRA BENEFIT AND DOES NOT AFFECT
CONSUMERS’ STATUTORY RIGHTS.
UK
PRODUCT REGISTRATION
Visit www.vtech.co.uk/clubvtech/login
to register your VTech product
By joining the VTech Club you can also enter competitions,
find out about news and events, seek expert advice for parents
and let your kids play fun learning games and activities.
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für VTech LM808-1W wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info