Bedienungsanleitung Whirlpool WHM3111 (Seite 3 von 5) (Englisch)

633290

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

APPLIANCE DEFROSTING

The appliance should be defrosted when the thickness of

ice on the walls reaches 5-6 mm.

• Disconnect the appliance from the power supply.

• Remove food from the appliance and put it in a very

cool place or a thermally insulated bag.

• Leave the appliance door open.

• Remove the internal defrost water drain plug (depending

on model) (Fig. 8).

• Remove the external defrost water drain plug

(depending on model) and reposition it as shown in

g. 8.

• Use the separator (depending on model) inside the

product as a recipient for any remaining water, (D) as

shown in g. 8. If there is no separator, use a shallow

container.

• Defrosting can be sped up by using a spatula to detach

the frost from the appliance walls.

• Remove the frost from the bottom of the appliance.

• In order to avoid permanent damage to the

appliance interior, do not use pointed or sharp

metal instruments to remove the ice.

• Do not use abrasive products or heat up the

interior articially.

• Dry the inside of the appliance thoroughly.

• Ret the plug after defrosting.

CLEANING AND MAINTENANCE

• Remove the frost from the upper edges (see

Troubleshooting Guide).

• Clean the inside after defrosting, using a sponge

dampened with warm water and/or mild detergent.

• Clean the side vent (if provided).

Unplug the appliance before carrying out maintenance

operations. Do not use abrasive products, scourers

or stain-removers (e.g. acetone, trichloroethylene) to

clean the appliance.

To obtain the best results from your appliance, carry

out cleaning and maintenance at least once a year.

HANGING THE LID LIGHT BULB (if provided)

• Disconnect the appliance from the mains power supply.

• Remove the diuser by following the sequence of steps

shown in the gure.

• Unscrew the light bulb and replace it with an identical

bulb of the same wattage and voltage.

• Ret the diuser and plug in the appliance.

TROUBLESHOOTING GUIDE

1. The red LED (if provided) remains alight.

• Is there a power failure?

• Is defrosting in progress?

• Is the appliance lid properly closed?

• Is the appliance positioned near a heat source?

• Is the thermostat setting correct?

• Are the ventilation grille and condenser clean?

2. The appliance is too noisy.

• Is the appliance perfectly horizontal?

• Is the appliance in contact with other furniture or objects

that may cause vibrations?

• Has the packaging been removed from under the

appliance?

Note: Gurgling noises from the refrigerating circuit after the

compressor cuts out are perfectly normal.

3. The green LED (if provided) is o and the

appliance is not working.

• Is there a power failure?

• Is the plug properly inserted in the socket?

• Is the electric cable intact?

4. The green LED (if provided) is o and the

appliance is working.

• The green LED is not working. Contact the After Sales

Service for a replacement.

5. The compressor runs continuously.

• Have hot foods been put in the appliance?

• Has the appliance lid been left open for a long time?

• Is the appliance positioned in a very warm room or near

heat sources?

• Is the thermostat setting correct?

• Has the fast freeze function (depending on model) been

pressed by mistake?

6. Too much ice on the upper edge.

• Are the defrost water drainage plugs correctly

positioned?

• Is the appliance lid properly closed?

• Is the appliance lid seal damaged or deformed? (See

chapter “Installation”)

• Have the 4 protection pieces been removed? (See

chapter “Installation”)

7. Condensation forms on the external walls of the

appliance

• It is normal for condensation to form under certain

atmospheric conditions (humidity above 85%) or if the

appliance is located in a damp or poorly ventilated

room.

The performance of the appliance is in no way aected.

8. The layer of ice on the internal walls of the

appliance is not uniform.

• This phenomenon is quite normal.

SAFEGUARDING THE ENVIRONMENT

1. Packing

The packing material is 100% recyclable and bears the

recycling symbol

. For disposal, comply with the local

regulations. Keep the packing materials (plastic bags,

polystyrene parts, etc.) out of the reach of children, as they

are a potential source of danger.

2. Scrapping/Disposal

The appliance is manufactured using recyclable material.

This appliance is marked in compliance with European

Directive 2002/96/EC on Waste Electrical and Electronic

Equipment (WEEE). By ensuring the correct disposal of

this appliance, you can help prevent potentially negative

consequences for the environment and the health of

persons.

The symbol

on the appliance, or on the accompanying

documents, indicates that this appliance should not be

treated as domestic waste but must be taken to a special

collection centre for the recycling of electrical and electronic

equipment.

When scrapping the appliance, make it unusable by cutting

o the power cable and removing the doors and shelves

so that children cannot easily climb inside and become

trapped.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool WHM3111 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool WHM3111

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info