Bedienungsanleitung White Knight WM126M (Seite 4 von 12) (Englisch)

484212

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

P.06

P.07

Installation Instructions

3.Loosen the lock nut with a spanner and turn the foot by hand until it contacts the floor.

Hold the foot with one hand and fasten the nut against the cabinet with a spanner.

4.Press the four top corners again to check that the feet have been adjusted properly.

If the machine is still unstable repeat steps 2 and 3.

5.Put a solid cylinder (e.g. pop can) on the top cover of the washing machine in the left,

right, front and back positions. If it rolls then the machine is not level. The rolling direction

is the direction of the ground surface. The two legs in this direction need to be raised

at the same time until the washing machine is level. Once the machine is level ensure

that all the nuts are locked tight.

Connect the inlet pipe as indicated in the figure.

This machine only has a cold water inlet.

The water inlet pipe should be connected to

a ¾” threaded water tap

1. Connect the end of the pipe, with an elbow,

to the water inlet valve on the rear of the machine.

Tighten the nut clockwise.

2. Connect the other end of the inlet pipe to the

water tap.

Turn on the tap and ensure that there is no water

leakage.

There are three possible ways to connect the outlet hose to a suitable drain.

1. Position the outlet hose into a sink.

Inlet Pipe Connection

Installing the Inlet Pipe

Installing the Outlet Hose

Unpacking the Washing Machine

Unpack the washing machine and check that there is no transport damage.

Ensure that all the items (as shown on page 5) are included in the enclosed bag.

If there is any damage to the washing machine during transportation or any items

are missing, please contact your retailer immediately.

The packaging materials of this machine may be dangerous to children.

Please dispose of them properly in accordance with the local regulations.

Please do not throw the packaging materials away with general household waste.

Before using the washing machine the transport bolts

must be removed from the rear of the machine.

Please take the following steps to remove the bolts:

1. Loosen all 4 bolts with a spanner and remove them.

2. Stop the holes with the transport hole plugs provided.

3. Keep the transport bolts for future use.

The washing machine must be installed in a location with the following characteristics:

-Rigid, dry and level surface (if not level please refer to the following section “Adjusting the Feet”)

-Avoid direct sunlight

-Room temperature above 0°C

-Away from sources of heat

Ensure that the washing machine is not standing on the power cord.

Do not install the washing machine on a carpeted floor.

1.When positioning the washing machine please check

that all the feet are fully screwed into the cabinet. If not,

please turn them to their original positions and tighten

the nuts with a spanner.

2.After positioning the washing machine, press all four

corners on the top of the washing machine in sequence.

If the washing machine is not stable when being pressed,

this foot should be adjusted.

Disposal of the Packaging Materials

Removing the Transport Bolts

Selecting the Location

Adjusting the Feet

Installation Instructions

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

White Knight WM126M Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info