674747
31
Zoom out
Zoom in
Vorherige Seite
1/140
Nächste Seite
Page 29FT
DX
1200 OPERATING MANUAL
REAR PANEL
ANT 1/2 Jacks
Connect your main antennas) here, using type-0
3L-) connectors and coaxial feed lines. The in-
ternal antenna tuner affects only the antennas) con-
nected here, and only during transmission.
Warning!
7KH95)YROWDJH#:ȍLVDSSOLHGWR
the TX RF section of the transceiver while trans-
mitting. Do not touch the TX RF section while
transmitting.
DC IN Jack
This is the 'C power supply connection for the
transceiver. Use the supplied 'C cable to connect di-
rectly to a 'C power supply, which must be capable
of supplying at least 3 $ #13.8 V'C.
GND
Use this terminal to connect the transceiver to a good
earth ground, for safety and optimum performance.
Use a large diameter, short braided cable for making
ground connections, and please refer to page for
other notes about proper grounding.
To prevent damage from lightning, atmo-
spheric electricity, electrical shock, etc., be
certain to provide a good earth ground.
μ-TUNE Jacks
These jacks are used to connect the optional 5F
Tuning .it, signal in and signal out.
ROT Jack
This covered 6-pin 0I1I-'I1 -ack accepts a cable
to connect to a Y$(SU
G-800DXA
-1000DXA/
-2800DXA
$ntenna 5otator listed models are cur-
rent as of early 013). You may control the antenna
a]imuth rotation and rotation speed) using the Func-
tion buttons on the front panel.
LINEAR Jack
This 10-pin output jack provides band selection data,
which may be used for control of optional accesso-
ries such as the
VL-1000
Solid-state Linear $mpli-
¿er.
TUNER Jack
This 8-pin output jack is used for connection to the
FC-40
(xternal $utomatic $ntenna Tuner.
RTTY/DATA Jack
This 6-pin inputoutput jack accepts $FS. input
from a Terminal 1ode Controller T1C) or an op-
tional interface unit it also provides ¿xed level 100-
mV #600 2hms) receiver audio output, and FS.
keying line.
PTT Jack
This 5C$ input jack may be used to provide manual
transmitter activation using a footswitch or other
switching device. Its function is identical to the
[
MOX
]
button on the front panel. The same line is
available at the
RTTY/PKT
jack for T1C control.
2pen-circuit voltage is  V'C, and closed-circuit
current is m$.
31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yaesu FTDX1200 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info