Bedienungsanleitung Zelmer 619 (Seite 90 von 92) (Englisch, Polnisch)

539643

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

− Pour dirty water out including the dirtiness form the tank and rinse the tank.

− Insert the water filter without paper bag and filtration pad.

− Place the tank at the base and close the top lid.

− Remove the nozzle or the brush, which was used earlier

and fit the nozzle for wet clearing on the sucking tube.

− Remove the back tank:

− open the top lid and bring it to vertical position 1.

− move the tank up and then move it back 2.

− Remove the inlet pin and fill the tank up with cleaning agents

(the powder solution or liquid), according to the label:

1. Powder, cleaning solution preparation: dissolve the content

of the bag in 2,5 – 3l of warm water- temp. up to 45ºC.

2. Cleaning liquid: pour the measured portion of the liquid into

the back tank. 1 pin of liquid for 3,5l water.

− Depending on the applied clearing agent, fill the back tank up with prepared solution or warm water

with temp. up to 45ºC.

− Insert the pin into the inlet in back tank.

ZELMER S.A. warranties good cleaning effect and proper vacuum cleaner operation, only using the

cleaning agents and their amount approved by ZELMER S.A., which is indicated at the label:

− „DYWANOPUC” cleaning powder manufactured by OKTIMA,Poland,

− „CARPEX” cleaning liquid manufactured by ASTRA POLLENA, Poland,

− „FOUNTAINHEAD” cleaning liquid manufactured by Butcher’s, USA

− Place the tank in previous place and push it in to fasten it exactly at the vacuum

cleaner housing.

− Close the top lid.

ATTENTION !!! The vacuum cleaner is equipped by the manufacturer with one

of the a/m cleaning agents only.

CLEANING CARPETS

heck the colours resistance before wet cleaning.

Put a small amount of cleaning agent on white cloth (powder solution or liquid) and clean the carpet in

the least visible place. If the cloth will be coloured, it means that the carpet does not have permanent

colours and can not be cleaned this way.

To protect against foam generation, or when it is generated during cleaning, use the anti-

foaming agent recommended by ZELMER S.A., in amount and way explained at the label:

− “G 478 Entschäumer D” manufactured by BUZIL, Germany.

− „FOAM-FREE” provided by Butcher’s, US.

ATTENTION!!! The vacuum cleaner is equipped by the manufacturer with one

of the a/m cleaning agents only.

− Remove the brush strip from the nozzle

− Check the right direction of nozzle movement on the carpet, so that it has the least

friction.

− Press the pump on/off button in and switch

the vacuum cleaner on.

ATTENTION!!! You can switch the pump on only, when there is water

inside the back tank. The lack of water is indicated with very noisy pump operation.

− Press the adjusting button at the hose handle to adjust the water flow to the nozzle.

− Move the nozzle along the carpet with forward and backward movements.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zelmer 619 Seite 90

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info