Bedienungsanleitung Zelmer 619 (Seite 92 von 92) (Englisch, Polnisch)

539643

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

− Remove the water filter from the tank.

− Remove the foam filter from the water filter and rinse it under running water

from the inside of the foam.

ATTENTION!!! Do not wash the filtration foam in hand by wringing it or in

washing machines Avoid squashing, stretching or

deformation. Dry after washing in ambient temperature

straightened or hanged on the handle.

Never dry the foam on the heaters, radiators, ovens, etc.

− Pour the dirty water out through the inlet for hose assembling.

− Clean the tank and water filter thoroughly, change the water some times.

− After washing clean thoroughly all the elements of accessories used during this

process (hose, tubes, accessories).

Leaving the a/m parts unclean or not exactly cleaned can cause the loss of

filtration abilities of the pads and foam and enhance bacteria and mites development.

− Dry all the cleaned parts thoroughly.

ATTENTION!!! Never assemble the vacuum cleaner before drying cleaned parts.

− Insert the water filter, place the tank on the base and close the top lid.

FILTERS REPLACEMENT

Air-inlet and air-outlet filters get dirty during operation. It is recommended to flush air-inlet filter to

provide proper operation. Very dirty or damaged air-inlet filter must be replaced with a new one.

Air inlet filter replacing

− Open the vacuum cleaner lid and place it in vertical position.

− Catch the upper edge of the filter grid (from the front) and pull it slightly in your

direction until it gets out of the hooks.

− Turn the frame, remove the filter, rinse it under running water, press slightly, dry

and replace (or replace with a new one).

− Place the new filter thoroughly, so that after closing the frame, its edges were

tightly pressing the filter edge.

− Close the filter frame.

Air-outlet filter

The air-outlet filter should be exchanged after about 30 operational hours (6 months),

or earlier in case of strong dirtiness.

− Press the cocker and open the outlet cover.

− Exchange the filter insert:

Type 619.5*E – fig. A; Type 619.5*S – fig. B

Electrostatic filter Cassette with HEPA filter

− Insert the filter thoroughly (fig. A), so

that after closing the frame, its edges

were tightly pressing the filter edge.

If any water occurs at air-outlet filter, it means that there is some foam inside the front tank,

which condenses at the air-outlet filter, after getting through the turbine. In order to avoid such

phenomenon it is required to add foam neutralizing agent recommended by ZELMER S.A., and

switch on for some minutes (without front tank) in order to dry the suction system.

Air-outlet filter should be always replaced with a brand- new, original one.

ECOLOGY

At the end the product’s useful life, please dispose of it at appropriate collection points

provided in your country.

619-195

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zelmer 619 Seite 92

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info