Bedienungsanleitung Zelmer Solaris 5000.0 HQ (Seite 46 von 50) (Englisch, Polnisch)

539689

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

52 5000-017_v02

Preparing the vacuum cleaner for

operation

Insert the curved hose end in the opening of the vacuum

cleaner and gently press. A characteristic click indicates that

the hose has been properly installed.

Connect the other end of the hose (handle) with the

telescopic suction tube. In order to do so press the locking

device “A” and slide the tube into the hose handle so that

the locking device “A” is blocked in opening “B”.

Adjust the length of the telescopic suction tube by sliding

the slider according to the arrow and pull out/ pull the tube

together.

Assemble the appropriate nozzle or brush to the other

end of the suction tube.

You may assemble a basket for picking up small objects

in the combination brush with the small item separator. In

order to do so remove the blank cover and insert the basket.

To clean hard surfaces – wooden oors, plastic oors,

ceramic tiles etc. pull out the brush by pressing the switch on

the combination brush according to the gure .

Grab the plug (3) and pull the cord out of the vacuum

cleaner.

 Whilepulingoutthecordpayattentiontothe

yellowstripewhichsignalstheendofthecord.

Furtherattempts(pullingoncord)mayresultin

damagingthecord.

The vacuum cleaner is equipped with an „Autorevers“

function, which provides automatic cord rewinding without

necessity of constant pressing the cord rewind knob (12).

In order to start up the function, move the „Autorevers” (11)

knob to position AUTO.

Plug in the appliance.

Before operation make sure that the SAFBAG bag is installed

in the vacuum cleaner chamber and that inlet lter and the

HEPA outlet lter is installed in the appliance.

Switch on the vacuum cleaner by pressing the “on/off”

button (7).

The vacuum cleaner is equipped with an electronic power

control which allows to gradually adjust the vacuum cleaner

suction power during operation. To adjust the suction power

use the power adjustment buttons (6,8) – – to increase

the suction power or – to decrease the suction power.

The suction power setting is indicated by the appropriate

number of lit diodes.

The vacuum cleaner will by default begin operation at the

medium power range. 3 diodes will light on the suction power

level indicator (9).

The suction power may be adjusted during operation.

The recommended settings are:

Setting 1 – vacuuming curtains

Setting 2 – vacuuming upholstery

Setting 3 – cost-effective power

Setting 4 – vacuuming carpets

Setting 5 – vacuuming hard oors and crevices.

The vacuum cleaner type 5000.3 is additionally equipped

with remote suction power control located in the suction hose

handle. It allows to change the suction power without the

necessity to bend down.

In order to use this function, open the battery compartment

in the suction hose handle and insert two1.5V AAA type

batteries or two chargeable 1.2 V AAA type batteries.

 Insert the batteries so that the battery pole

market“+”isalwaysdirectedtowardsthelock

ofthecompartmentmarkedwith“+”.

Use only high quality batteries. Battery leakage may

cause damage to the electronic system.

To use the remote control of the suction power press the

appropriate button on the hose handle ( , ):

To increase the suction power by one setting press the –

button.

To decrease the suction power by one setting press the –

button.

Press the button on the hose handle to temporarily

switch off the appliance and to operate in the STANDBY

mode.

To continue vacuuming press the STANDBY button (18) once

again. The appliance will start operating with the previously

set suction power.

 Theinfrared transmitter and receiver have to

“see”eachotherinorderfortheremotecontrol

systemtoworkproperly.

The vacuum cleaner is equipped with accessories

compartment. In order to open the compartment pull up the

cover of the accessories compartment (16).

The accessories may be attached to the accessory

holder in the suction hose handle. This way they will be

available for use at any time.

The vacuum cleaner is equipped with the “Parksystem”

function. This function allows to temporarily switch off the

vacuum cleaner using the fastening hook of the combination

brush without the necessity to use the on/off button. In order

to do so, during operation insert the fastening hook of the

combination brush in the combination brush fastening (4).

The vacuum cleaner will automatically switch off.

Filter disassembly

Before changing the lters make sure that the vacuum cleaner

is switched off and unplugged from the mains supply.

INLET FILTER

Release the fastener of the front cover

●

(15) and open it.

Remove the SAFBAG dust bag module from the vacuum

●

cleaner chamber.

Slide the inlet lter casing with the installed inlet lter from

the tracks on the back side of the vacuum cleaner chamber.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zelmer Solaris 5000.0 HQ Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info